Steel P460QL1-QT vs P460QL1 QT-100-150
Steel · P460QL1 temper comparison
P460QL1-QT and P460QL1 QT-100-150 are two conditions of the same steel grade, P460QL1: QT (quenched and tempered) versus QT-100-150 (QT). The chemistry is identical, so every difference below comes from the condition. P460QL1-QT is the stronger of the two: yield strength 500 MPa (72.5 ksi) against 440 MPa (63.8 ksi) for P460QL1 QT-100-150, about 14% more; tensile strength follows at 630 MPa (91.4 ksi) vs 580 MPa (84.1 ksi). P460QL1-QT is harder — 210 HB against 190 HB for P460QL1 QT-100-150 — which matters for wear surfaces and threads.
P460QL1-QTChoose it when strength drives the design, or when surface hardness matters.
P460QL1-QT vs P460QL1 QT-100-150: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 40 W/m·K23.1 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.2 % IACS · Electrical Resistivity 2.4×10⁻⁷ Ω·m9.45 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 40 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
P460QL1-QT vs P460QL1 QT-100-150 — frequently asked
Is P460QL1-QT stronger than P460QL1 QT-100-150?
Yes. P460QL1-QT has a typical yield strength of 500 MPa (72.5 ksi) against 440 MPa (63.8 ksi) for P460QL1 QT-100-150 — about 14% more. Tensile strength is 630 MPa (91.4 ksi) vs 580 MPa (84.1 ksi).
Which condition does FabDigit quote by default, QT or QT-100-150?
QT is the default P460QL1 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, P460QL1-QT or P460QL1 QT-100-150?
P460QL1 QT-100-150. Its machinability rates good (55/100) against fair (50/100) for P460QL1-QT.
Ready to make it?
Upload a CAD file and FabDigit prices the part in P460QL1-QT and P460QL1 QT-100-150 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.