Steel P195TR2 +A vs P195TR2 +SR
Steel · P195TR2 temper comparison
P195TR2 +A and P195TR2 +SR are two conditions of the same steel grade, P195TR2: +A (annealed) versus +SR (stress relieved). The chemistry is identical, so every difference below comes from the condition. P195TR2 +SR is the stronger of the two: yield strength 280 MPa (40.6 ksi) against 210 MPa (30.5 ksi) for P195TR2 +A, about 33% more; tensile strength follows at 400 MPa (58 ksi) vs 340 MPa (49.3 ksi). In exchange, P195TR2 +A is the more ductile: elongation 36% versus 24% for P195TR2 +SR, and P195TR2 +SR is harder (130 HB vs 105 HB).
P195TR2 +AChoose it when the part is bent, formed or impact-loaded.
P195TR2 +SRChoose it when strength drives the design.
P195TR2 +A vs P195TR2 +SR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,490°C2,714 °F · Liquidus Temperature 1,525°C2,777 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 52 W/m·K30 BTU/hr·ft·°F · Specific Heat Capacity 465 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 247 J/g106 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -10°C14 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 75 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 1.9 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
P195TR2 +A vs P195TR2 +SR — frequently asked
Is P195TR2 +SR stronger than P195TR2 +A?
Yes. P195TR2 +SR has a typical yield strength of 280 MPa (40.6 ksi) against 210 MPa (30.5 ksi) for P195TR2 +A — about 33% more. Tensile strength is 400 MPa (58 ksi) vs 340 MPa (49.3 ksi).
Which condition does FabDigit quote by default, +A or +SR?
+N is the default P195TR2 condition in the FabDigit quote flow (neither +A nor +SR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, P195TR2 +A or P195TR2 +SR?
P195TR2 +SR. Its machinability rates good (58/100) against fair (52/100) for P195TR2 +A.
Ready to make it?
Upload a CAD file and FabDigit prices the part in P195TR2 +A and P195TR2 +SR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.