Steel Nitralloy N-ANN vs Nitralloy N-N
Steel · Nitralloy N temper comparison
Nitralloy N-ANN and Nitralloy N-N are two conditions of the same steel grade, Nitralloy N: ANN (annealed) versus N (normalized). The chemistry is identical, so every difference below comes from the condition. Nitralloy N-N is the stronger of the two: yield strength 650 MPa (94.3 ksi) against 520 MPa (75.4 ksi) for Nitralloy N-ANN, about 25% more; tensile strength follows at 900 MPa (131 ksi) vs 760 MPa (110 ksi). In exchange, Nitralloy N-ANN is the more ductile: elongation 24% versus 20% for Nitralloy N-N, and Nitralloy N-N is harder (269 HB vs 217 HB). Nitralloy N-ANN runs hotter in service (500°C vs 450°C continuous).
Nitralloy N-ANNChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Nitralloy N-NChoose it when strength drives the design.
Nitralloy N-ANN vs Nitralloy N-N: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,480°C2,696 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.6 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 16 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 30 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.6 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Nitralloy N-ANN vs Nitralloy N-N — frequently asked
Is Nitralloy N-N stronger than Nitralloy N-ANN?
Yes. Nitralloy N-N has a typical yield strength of 650 MPa (94.3 ksi) against 520 MPa (75.4 ksi) for Nitralloy N-ANN — about 25% more. Tensile strength is 900 MPa (131 ksi) vs 760 MPa (110 ksi).
Which condition does FabDigit quote by default, ANN or N?
QT30-36HRC is the default Nitralloy N condition in the FabDigit quote flow (neither ANN nor N). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Nitralloy N-ANN or Nitralloy N-N?
Nitralloy N-ANN, by a small margin. Both rate fair for machinability — 52/100 against 46/100 for Nitralloy N-N.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Nitralloy N-ANN and Nitralloy N-N side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.