Steel J422-AW vs J422-SR
Steel · J422 temper comparison
J422-AW and J422-SR are two conditions of the same steel grade, J422: AW (as-welded deposit) versus SR (stress relieved). The chemistry is identical, so every difference below comes from the condition. J422-AW is the stronger of the two: yield strength 400 MPa (58 ksi) against 360 MPa (52.2 ksi) for J422-SR, about 11% more; tensile strength follows at 490 MPa (71.1 ksi) vs 465 MPa (67.4 ksi). In exchange, J422-SR is the more ductile: elongation 29% versus 26% for J422-AW, and J422-AW is harder (160 HB vs 145 HB). J422-SR runs hotter in service (400°C vs 350°C continuous).
J422-AWChoose it when strength drives the design.
J422-SRChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
J422-AW vs J422-SR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,500°C2,732 °F · Liquidus Temperature 1,530°C2,786 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 272 J/g117 BTU/lb · Min Service Temperature 0°C32 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 12 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 95 / 100 · Brazeability / Solderability 70 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 35 MJ/kg15,047 BTU/lb · Embodied Carbon (primary production) 2.6 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
J422-AW vs J422-SR — frequently asked
Is J422-AW stronger than J422-SR?
Yes. J422-AW has a typical yield strength of 400 MPa (58 ksi) against 360 MPa (52.2 ksi) for J422-SR — about 11% more. Tensile strength is 490 MPa (71.1 ksi) vs 465 MPa (67.4 ksi).
Which condition does FabDigit quote by default, AW or SR?
AW is the default J422 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, J422-AW or J422-SR?
J422-SR, by a small margin. Both rate good for machinability — 60/100 against 55/100 for J422-AW.
Ready to make it?
Upload a CAD file and FabDigit prices the part in J422-AW and J422-SR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.