Steel HC300LA-CR vs HC300LA +ZF
Steel · HC300LA temper comparison
HC300LA-CR and HC300LA +ZF are two conditions of the same steel grade, HC300LA: CR (cold rolled) versus +ZF (galvannealed zinc-iron coating). The chemistry is identical, so every difference below comes from the condition. Both yield at about 335 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (cold rolled versus galvannealed zinc-iron coating). HC300LA-CR is the more ductile: elongation 28% versus 25% for HC300LA +ZF. HC300LA-CR runs hotter in service (300°C vs 250°C continuous).
HC300LA-CRChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
HC300LA-CR vs HC300LA +ZF: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 166 GPa24.1 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,495°C2,723 °F · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 48 W/m·K27.7 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 10 % IACS · Electrical Resistivity 1.8×10⁻⁷ Ω·m7.09 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 60 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
HC300LA-CR vs HC300LA +ZF — frequently asked
What is the difference between HC300LA-CR and HC300LA +ZF?
HC300LA-CR and HC300LA +ZF are two conditions of the same steel grade, HC300LA: CR (cold rolled) versus +ZF (galvannealed zinc-iron coating). The chemistry is identical, so every difference below comes from the condition. Both yield at about 335 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (cold rolled versus galvannealed zinc-iron coating).
Which condition does FabDigit quote by default, CR or +ZF?
CR is the default HC300LA condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, HC300LA-CR or HC300LA +ZF?
HC300LA-CR. Its weldability rates excellent (88/100) against very good (82/100) for HC300LA +ZF.
Ready to make it?
Upload a CAD file and FabDigit prices the part in HC300LA-CR and HC300LA +ZF side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.