Steel G25NiCrMo6 +N vs G25NiCrMo6 +QT2
Steel · G25NiCrMo6 temper comparison
G25NiCrMo6 +N and G25NiCrMo6 +QT2 are two conditions of the same steel grade, G25NiCrMo6: +N (normalized) versus +QT2 (quenched and tempered, higher strength class). The chemistry is identical, so every difference below comes from the condition. G25NiCrMo6 +QT2 is the stronger of the two: yield strength 750 MPa (109 ksi) against 480 MPa (69.6 ksi) for G25NiCrMo6 +N, about 56% more; tensile strength follows at 960 MPa (139 ksi) vs 720 MPa (104 ksi). In exchange, G25NiCrMo6 +N is the more ductile: elongation 15% versus 10% for G25NiCrMo6 +QT2, and G25NiCrMo6 +QT2 is harder (290 HB vs 215 HB). On the shop floor, G25NiCrMo6 +N machines more easily (good vs fair) and G25NiCrMo6 +N welds better (fair vs poor).
G25NiCrMo6 +NChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
G25NiCrMo6 +QT2Choose it when strength drives the design.
G25NiCrMo6 +N vs G25NiCrMo6 +QT2: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 208 GPa30.2 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.83 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 380°C716 °F · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 16 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 65 / 100 · Brazeability / Solderability 45 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 27 MJ/kg11,608 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 80%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
G25NiCrMo6 +N vs G25NiCrMo6 +QT2 — frequently asked
Is G25NiCrMo6 +QT2 stronger than G25NiCrMo6 +N?
Yes. G25NiCrMo6 +QT2 has a typical yield strength of 750 MPa (109 ksi) against 480 MPa (69.6 ksi) for G25NiCrMo6 +N — about 56% more. Tensile strength is 960 MPa (139 ksi) vs 720 MPa (104 ksi).
Which condition does FabDigit quote by default, +N or +QT2?
+QT1 is the default G25NiCrMo6 condition in the FabDigit quote flow (neither +N nor +QT2). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, G25NiCrMo6 +N or G25NiCrMo6 +QT2?
G25NiCrMo6 +N. Its machinability rates good (55/100) against fair (38/100) for G25NiCrMo6 +QT2; for welding the order is G25NiCrMo6 +N first (fair, 45/100) then G25NiCrMo6 +QT2 (poor, 33/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in G25NiCrMo6 +N and G25NiCrMo6 +QT2 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.