Steel G24Mn6 +A vs G24Mn6 +N
Steel · G24Mn6 temper comparison
G24Mn6 +A and G24Mn6 +N are two conditions of the same steel grade, G24Mn6: +A (annealed) versus +N (normalized). The chemistry is identical, so every difference below comes from the condition. G24Mn6 +N is the stronger of the two: yield strength 340 MPa (49.3 ksi) against 300 MPa (43.5 ksi) for G24Mn6 +A, about 13% more; tensile strength follows at 580 MPa (84.1 ksi) vs 520 MPa (75.4 ksi). In exchange, G24Mn6 +A is the more ductile: elongation 23% versus 20% for G24Mn6 +N, and G24Mn6 +N is harder (170 HB vs 150 HB).
G24Mn6 +AChoose it when the part is bent, formed or impact-loaded.
G24Mn6 +NChoose it when strength drives the design.
G24Mn6 +A vs G24Mn6 +N: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 350°C662 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 72 / 100 · Brazeability / Solderability 55 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 24 MJ/kg10,318 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 80%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
G24Mn6 +A vs G24Mn6 +N — frequently asked
Is G24Mn6 +N stronger than G24Mn6 +A?
Yes. G24Mn6 +N has a typical yield strength of 340 MPa (49.3 ksi) against 300 MPa (43.5 ksi) for G24Mn6 +A — about 13% more. Tensile strength is 580 MPa (84.1 ksi) vs 520 MPa (75.4 ksi).
Which condition does FabDigit quote by default, +A or +N?
+QT1 is the default G24Mn6 condition in the FabDigit quote flow (neither +A nor +N). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose G24Mn6 +A over G24Mn6 +N?
Pick G24Mn6 +A when the part is bent, formed or impact-loaded. Pick G24Mn6 +N when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in G24Mn6 +A and G24Mn6 +N side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.