Steel EN24-CR vs EN24 Normalized
Steel · EN24 temper comparison
EN24-CR and EN24 Normalized are two conditions of the same steel grade, EN24: CR (cold rolled) versus Normalized. The chemistry is identical, so every difference below comes from the condition. EN24 Normalized is the stronger of the two: yield strength 860 MPa (125 ksi) against 700 MPa (102 ksi) for EN24-CR, about 23% more; tensile strength follows at 1,280 MPa (186 ksi) vs 900 MPa (131 ksi). EN24 Normalized is the more ductile: elongation 12% versus 9% for EN24-CR, and EN24 Normalized is harder (363 HB vs 265 HB). EN24 Normalized runs hotter in service (400°C vs 300°C continuous). On the shop floor, EN24-CR machines more easily (good vs fair).
EN24-CRChoose it when the part is machined in volume.
EN24 NormalizedChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
EN24-CR vs EN24 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Charpy V-Notch Impact (RT) 25 J18.4 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 45 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
EN24-CR vs EN24 Normalized — frequently asked
Is EN24 Normalized stronger than EN24-CR?
Yes. EN24 Normalized has a typical yield strength of 860 MPa (125 ksi) against 700 MPa (102 ksi) for EN24-CR — about 23% more. Tensile strength is 1,280 MPa (186 ksi) vs 900 MPa (131 ksi).
Which condition does FabDigit quote by default, CR or Normalized?
HR is the default EN24 condition in the FabDigit quote flow (neither CR nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, EN24-CR or EN24 Normalized?
EN24-CR. Its machinability rates good (55/100) against fair (40/100) for EN24 Normalized; for welding the order is EN24 Normalized first (poor, 30/100) then EN24-CR (poor, 25/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in EN24-CR and EN24 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.