Steel A369 FP11-A vs A369 FP11 N+T
Steel · A369 FP11 temper comparison
A369 FP11-A and A369 FP11 N+T are two conditions of the same steel grade, A369 FP11: A (solution annealed) versus N+T (normalized and tempered). The chemistry is identical, so every difference below comes from the condition. A369 FP11 N+T is the stronger of the two: yield strength 330 MPa (47.9 ksi) against 285 MPa (41.3 ksi) for A369 FP11-A, about 16% more; tensile strength follows at 510 MPa (74 ksi) vs 470 MPa (68.2 ksi). In exchange, A369 FP11-A is the more ductile: elongation 32% versus 28% for A369 FP11 N+T, and A369 FP11 N+T is harder (155 HB vs 140 HB).
A369 FP11-AChoose it when the part is bent, formed or impact-loaded.
A369 FP11 N+TChoose it when strength drives the design.
A369 FP11-A vs A369 FP11 N+T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,490°C2,714 °F · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 465 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 565°C1,049 °F · Min Service Temperature -29°C-20 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 18 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 32 MJ/kg13,758 BTU/lb · Embodied Carbon (primary production) 2.4 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
A369 FP11-A vs A369 FP11 N+T — frequently asked
Is A369 FP11 N+T stronger than A369 FP11-A?
Yes. A369 FP11 N+T has a typical yield strength of 330 MPa (47.9 ksi) against 285 MPa (41.3 ksi) for A369 FP11-A — about 16% more. Tensile strength is 510 MPa (74 ksi) vs 470 MPa (68.2 ksi).
Which condition does FabDigit quote by default, A or N+T?
N+T is the default A369 FP11 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, A369 FP11-A or A369 FP11 N+T?
A369 FP11-A. Its weldability rates good (65/100) against good (60/100) for A369 FP11 N+T.
Ready to make it?
Upload a CAD file and FabDigit prices the part in A369 FP11-A and A369 FP11 N+T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.