Steel 8620 Normalized vs 8620 Q&T
Steel · 8620 temper comparison
8620 Normalized and 8620 Q&T are two conditions of the same steel grade, 8620: Normalized versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 8620 Q&T is the stronger of the two: yield strength 850 MPa (123 ksi) against 360 MPa (52.2 ksi) for 8620 Normalized, about 136% more; tensile strength follows at 1,050 MPa (152 ksi) vs 630 MPa (91.4 ksi). In exchange, 8620 Normalized is the more ductile: elongation 26% versus 15% for 8620 Q&T, and 8620 Q&T is harder (293 HB vs 183 HB). 8620 Normalized runs hotter in service (400°C vs 300°C continuous). On the shop floor, 8620 Normalized machines more easily (good vs fair) and 8620 Normalized welds better (good vs fair).
8620 NormalizedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
8620 Q&TChoose it when strength drives the design.
8620 Normalized vs 8620 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Shear Strength 390 MPa56.6 ksi
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,505°C2,741 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 46.6 W/m·K26.9 BTU/hr·ft·°F · Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.6 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 65 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
8620 Normalized vs 8620 Q&T — frequently asked
Is 8620 Q&T stronger than 8620 Normalized?
Yes. 8620 Q&T has a typical yield strength of 850 MPa (123 ksi) against 360 MPa (52.2 ksi) for 8620 Normalized — about 136% more. Tensile strength is 1,050 MPa (152 ksi) vs 630 MPa (91.4 ksi).
Which condition does FabDigit quote by default, Normalized or Q&T?
HR is the default 8620 condition in the FabDigit quote flow (neither Normalized nor Q&T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 8620 Normalized or 8620 Q&T?
8620 Normalized. Its machinability rates good (62/100) against fair (48/100) for 8620 Q&T; for welding the order is 8620 Normalized first (good, 62/100) then 8620 Q&T (fair, 45/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 8620 Normalized and 8620 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.