Steel 6152 Cold Drawn vs 6152 Normalized
Steel · 6152 temper comparison
6152 Cold Drawn and 6152 Normalized are two conditions of the same steel grade, 6152: Cold Drawn versus Normalized. The chemistry is identical, so every difference below comes from the condition. 6152 Cold Drawn is the stronger of the two: yield strength 700 MPa (102 ksi) against 615 MPa (89.2 ksi) for 6152 Normalized, about 14% more. In exchange, 6152 Normalized is the more ductile: elongation 22% versus 12% for 6152 Cold Drawn, and 6152 Normalized is harder (269 HB vs 240 HB). 6152 Normalized runs hotter in service (400°C vs 250°C continuous). On the shop floor, 6152 Cold Drawn machines more easily (good vs fair).
6152 Cold DrawnChoose it when strength drives the design, or when the part is machined in volume.
6152 NormalizedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
6152 Cold Drawn vs 6152 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
6152 Cold Drawn6152 Normalized
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 46 W/m·K26.6 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.5 % IACS · Electrical Resistivity 2.3×10⁻⁷ Ω·m9.06 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 13 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 30 / 100 · Brazeability / Solderability 55 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
6152 Cold Drawn vs 6152 Normalized — frequently asked
Is 6152 Cold Drawn stronger than 6152 Normalized?
Yes. 6152 Cold Drawn has a typical yield strength of 700 MPa (102 ksi) against 615 MPa (89.2 ksi) for 6152 Normalized — about 14% more. Tensile strength is 830 MPa (120 ksi) vs 940 MPa (136 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Normalized?
Annealed is the default 6152 condition in the FabDigit quote flow (neither Cold Drawn nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 6152 Cold Drawn or 6152 Normalized?
6152 Cold Drawn. Its machinability rates good (55/100) against fair (42/100) for 6152 Normalized.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 6152 Cold Drawn and 6152 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.