Steel 42CD4 +S vs 42CD4 +U
Steel · 42CD4 temper comparison
42CD4 +S and 42CD4 +U are two conditions of the same steel grade, 42CD4: +S (treated to improve shearability) versus +U (hot rolled). The chemistry is identical, so every difference below comes from the condition. 42CD4 +U is the stronger of the two: yield strength 560 MPa (81.2 ksi) against 400 MPa (58 ksi) for 42CD4 +S, about 40% more; tensile strength follows at 900 MPa (131 ksi) vs 640 MPa (92.8 ksi). In exchange, 42CD4 +S is the more ductile: elongation 24% versus 16% for 42CD4 +U, and 42CD4 +U is harder (255 HB vs 190 HB).
42CD4 +SChoose it when the part is bent, formed or impact-loaded.
42CD4 +UChoose it when strength drives the design.
42CD4 +S vs 42CD4 +U: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,416°C2,581 °F · Liquidus Temperature 1,495°C2,723 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 473 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 60 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
42CD4 +S vs 42CD4 +U — frequently asked
Is 42CD4 +U stronger than 42CD4 +S?
Yes. 42CD4 +U has a typical yield strength of 560 MPa (81.2 ksi) against 400 MPa (58 ksi) for 42CD4 +S — about 40% more. Tensile strength is 900 MPa (131 ksi) vs 640 MPa (92.8 ksi).
Which condition does FabDigit quote by default, +S or +U?
+QT is the default 42CD4 condition in the FabDigit quote flow (neither +S nor +U). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 42CD4 +S or 42CD4 +U?
42CD4 +S. Its machinability rates good (60/100) against fair (52/100) for 42CD4 +U.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 42CD4 +S and 42CD4 +U side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.