Steel 41B17-CD vs 41B17-HR
Steel · 41B17 temper comparison
41B17-CD and 41B17-HR are two conditions of the same steel grade, 41B17: CD (cold drawn) versus HR (hot rolled). The chemistry is identical, so every difference below comes from the condition. 41B17-CD is the stronger of the two: yield strength 505 MPa (73.2 ksi) against 330 MPa (47.9 ksi) for 41B17-HR, about 53% more; tensile strength follows at 590 MPa (85.6 ksi) vs 515 MPa (74.7 ksi). In exchange, 41B17-HR is the more ductile: elongation 27% versus 15% for 41B17-CD, and 41B17-CD is harder (174 HB vs 149 HB). On the shop floor, 41B17-CD machines more easily (68 vs 58 out of 100).
41B17-CDChoose it when strength drives the design, or when the part is machined in volume.
41B17-HRChoose it when the part is bent, formed or impact-loaded.
41B17-CD vs 41B17-HR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Shear Strength 330 MPa47.9 ksi · Fracture Toughness (K_IC) 90 MPa·√m81.9 ksi·√in
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 60 / 100 · Brazeability / Solderability 65 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 29 MJ/kg12,468 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
41B17-CD vs 41B17-HR — frequently asked
Is 41B17-CD stronger than 41B17-HR?
Yes. 41B17-CD has a typical yield strength of 505 MPa (73.2 ksi) against 330 MPa (47.9 ksi) for 41B17-HR — about 53% more. Tensile strength is 590 MPa (85.6 ksi) vs 515 MPa (74.7 ksi).
Which condition does FabDigit quote by default, CD or HR?
A is the default 41B17 condition in the FabDigit quote flow (neither CD nor HR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 41B17-CD or 41B17-HR?
41B17-CD, by a small margin. Both rate good for machinability — 68/100 against 58/100 for 41B17-HR.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 41B17-CD and 41B17-HR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.