Steel 40CrV-N vs 40CrV QT28-32HRC
Steel · 40CrV temper comparison
40CrV-N and 40CrV QT28-32HRC are two conditions of the same steel grade, 40CrV: N (normalized) versus QT28-32HRC (Q&T to 28–32 HRC). The chemistry is identical, so every difference below comes from the condition. 40CrV QT28-32HRC is the stronger of the two: yield strength 850 MPa (123 ksi) against 520 MPa (75.4 ksi) for 40CrV-N, about 63% more; tensile strength follows at 1,000 MPa (145 ksi) vs 800 MPa (116 ksi). In exchange, 40CrV-N is the more ductile: elongation 17% versus 14% for 40CrV QT28-32HRC, and 40CrV QT28-32HRC is harder (293 HB vs 235 HB). On the shop floor, 40CrV-N welds better (fair vs poor).
40CrV-NChoose it when the part is bent, formed or impact-loaded, or when it will be welded.
40CrV QT28-32HRCChoose it when strength drives the design.
40CrV-N vs 40CrV QT28-32HRC: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,495°C2,723 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 50 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.2 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
40CrV-N vs 40CrV QT28-32HRC — frequently asked
Is 40CrV QT28-32HRC stronger than 40CrV-N?
Yes. 40CrV QT28-32HRC has a typical yield strength of 850 MPa (123 ksi) against 520 MPa (75.4 ksi) for 40CrV-N — about 63% more. Tensile strength is 1,000 MPa (145 ksi) vs 800 MPa (116 ksi).
Which condition does FabDigit quote by default, N or QT28-32HRC?
QT is the default 40CrV condition in the FabDigit quote flow (neither N nor QT28-32HRC). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 40CrV-N or 40CrV QT28-32HRC?
40CrV-N. Its machinability rates good (55/100) against fair (48/100) for 40CrV QT28-32HRC; for welding the order is 40CrV-N first (fair, 40/100) then 40CrV QT28-32HRC (poor, 30/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 40CrV-N and 40CrV QT28-32HRC side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.