Steel 17CrNiMo6 Annealed vs 17CrNiMo6 Hot Rolled
Steel · 17CrNiMo6 temper comparison
17CrNiMo6 Annealed and 17CrNiMo6 Hot Rolled are two conditions of the same steel grade, 17CrNiMo6: Annealed versus Hot Rolled. The chemistry is identical, so every difference below comes from the condition. 17CrNiMo6 Hot Rolled is the stronger of the two: yield strength 560 MPa (81.2 ksi) against 430 MPa (62.4 ksi) for 17CrNiMo6 Annealed, about 30% more; tensile strength follows at 900 MPa (131 ksi) vs 700 MPa (102 ksi). In exchange, 17CrNiMo6 Annealed is the more ductile: elongation 20% versus 14% for 17CrNiMo6 Hot Rolled, and 17CrNiMo6 Hot Rolled is harder (270 HB vs 200 HB). 17CrNiMo6 Annealed runs hotter in service (300°C vs 200°C continuous). On the shop floor, 17CrNiMo6 Annealed machines more easily (50 vs 40 out of 100).
17CrNiMo6 AnnealedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
17CrNiMo6 Hot RolledChoose it when strength drives the design.
17CrNiMo6 Annealed vs 17CrNiMo6 Hot Rolled: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
17CrNiMo6 Annealed17CrNiMo6 Hot Rolled
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 38 W/m·K22 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.5 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 8 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 25 / 100 · Brazeability / Solderability 45 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 32 MJ/kg13,758 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
17CrNiMo6 Annealed vs 17CrNiMo6 Hot Rolled — frequently asked
Is 17CrNiMo6 Hot Rolled stronger than 17CrNiMo6 Annealed?
Yes. 17CrNiMo6 Hot Rolled has a typical yield strength of 560 MPa (81.2 ksi) against 430 MPa (62.4 ksi) for 17CrNiMo6 Annealed — about 30% more. Tensile strength is 900 MPa (131 ksi) vs 700 MPa (102 ksi).
Which condition does FabDigit quote by default, Annealed or Hot Rolled?
Annealed is the default 17CrNiMo6 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 17CrNiMo6 Annealed or 17CrNiMo6 Hot Rolled?
17CrNiMo6 Annealed, by a small margin. Both rate fair for machinability — 50/100 against 40/100 for 17CrNiMo6 Hot Rolled; for welding the order is 17CrNiMo6 Annealed first (poor, 30/100) then 17CrNiMo6 Hot Rolled (poor, 25/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 17CrNiMo6 Annealed and 17CrNiMo6 Hot Rolled side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.