Steel 15B35 vs 20MnVB
Steel · grade comparison
Steel 15B35 and 20MnVB are both steel grades. 20MnVB is the stronger of the two: yield strength 950 MPa (138 ksi) against 620 MPa (89.9 ksi) for 15B35, about 53% more; tensile strength follows at 1,150 MPa (167 ksi) vs 730 MPa (106 ksi). 20MnVB is harder — 360 HB against 217 HB for 15B35 — which matters for wear surfaces and threads. 15B35 runs hotter in service (350°C vs 200°C continuous) and 15B35 conducts electricity better (9.5 % IACS vs 8 % IACS). On the shop floor, 15B35 machines more easily (good vs fair) and 15B35 forms better (good vs poor).
15B35Choose it when the part sees heat, or when the part is machined in volume.
20MnVBChoose it when strength drives the design, or when surface hardness matters.
15B35 vs 20MnVB: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Fracture Toughness (K_IC)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Liquidus Temperature
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Thermal Expansion (CTE, 20–100 °C) 11.9 µm/m·K6.6 µin/in·°F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Castability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 30%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 15B35 | 20MnVB |
|---|---|---|
| Default condition | — | — |
| Relative cost | $ Budget | $ Budget |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 9 finishes: Copper Plating, Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Manganese Phosphate, Plasma Spray, Silver Plating, Zinc Phosphate.
15B35 vs 20MnVB — frequently asked
Is 20MnVB stronger than 15B35?
Yes. 20MnVB has a typical yield strength of 950 MPa (138 ksi) against 620 MPa (89.9 ksi) for 15B35 — about 53% more. Tensile strength is 1,150 MPa (167 ksi) vs 730 MPa (106 ksi).
Which is cheaper, 15B35 or 20MnVB?
Both sit in the same relative cost tier ($, budget); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, 15B35 or 20MnVB?
15B35. Its machinability rates good (55/100) against fair (38/100) for 20MnVB; for welding the order is 15B35 first (fair, 40/100) then 20MnVB (fair, 35/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 15B35 and 20MnVB side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.