Steel 13MoCrNi42-16-14-ANN vs 13MoCrNi42-16-14 HT-CORE
Steel · 13MoCrNi42-16-14 temper comparison
13MoCrNi42-16-14-ANN and 13MoCrNi42-16-14 HT-CORE are two conditions of the same steel grade, 13MoCrNi42-16-14: ANN (annealed) versus HT-CORE (hardened & tempered (core condition, no carburizing) 43–48 HRC). The chemistry is identical, so every difference below comes from the condition. 13MoCrNi42-16-14 HT-CORE is the stronger of the two: yield strength 1,200 MPa (174 ksi) against 560 MPa (81.2 ksi) for 13MoCrNi42-16-14-ANN, about 114% more; tensile strength follows at 1,500 MPa (218 ksi) vs 860 MPa (125 ksi). In exchange, 13MoCrNi42-16-14-ANN is the more ductile: elongation 18% versus 13% for 13MoCrNi42-16-14 HT-CORE, and 13MoCrNi42-16-14 HT-CORE is harder (428 HB vs 220 HB). 13MoCrNi42-16-14 HT-CORE runs hotter in service (315°C vs 200°C continuous). On the shop floor, 13MoCrNi42-16-14-ANN machines more easily (poor vs not recommended).
13MoCrNi42-16-14-ANNChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
13MoCrNi42-16-14 HT-COREChoose it when strength drives the design, or when the part sees heat.
13MoCrNi42-16-14-ANN vs 13MoCrNi42-16-14 HT-CORE: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
13MoCrNi42-16-14-ANN13MoCrNi42-16-14 HT-CORE
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 201 GPa29.2 Msi · Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Hardness, Rockwell B 97 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.78 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,460°C2,660 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 23 W/m·K13.3 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.3 µm/m·K6.3 µin/in·°F · Latent Heat of Fusion 265 J/g114 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.9 % IACS · Electrical Resistivity 6×10⁻⁷ Ω·m23.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 16 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 25 / 100 · Brazeability / Solderability 30 / 100 · Polishability 85 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 48 MJ/kg20,636 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 70 L/kg8.4 gal/lb · Typical Recycled Content 15%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
13MoCrNi42-16-14-ANN vs 13MoCrNi42-16-14 HT-CORE — frequently asked
Is 13MoCrNi42-16-14 HT-CORE stronger than 13MoCrNi42-16-14-ANN?
Yes. 13MoCrNi42-16-14 HT-CORE has a typical yield strength of 1,200 MPa (174 ksi) against 560 MPa (81.2 ksi) for 13MoCrNi42-16-14-ANN — about 114% more. Tensile strength is 1,500 MPa (218 ksi) vs 860 MPa (125 ksi).
Which condition does FabDigit quote by default, ANN or HT-CORE?
ANN is the default 13MoCrNi42-16-14 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 13MoCrNi42-16-14-ANN or 13MoCrNi42-16-14 HT-CORE?
13MoCrNi42-16-14-ANN. Its machinability rates poor (32/100) against not recommended (10/100) for 13MoCrNi42-16-14 HT-CORE; for welding the order is 13MoCrNi42-16-14-ANN first (poor, 15/100) then 13MoCrNi42-16-14 HT-CORE (not recommended, 8/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 13MoCrNi42-16-14-ANN and 13MoCrNi42-16-14 HT-CORE side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.