Steel 1345-A vs 1345-CD
Steel · 1345 temper comparison
1345-A and 1345-CD are two conditions of the same steel grade, 1345: A (solution annealed) versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. 1345-CD is the stronger of the two: yield strength 690 MPa (100 ksi) against 440 MPa (63.8 ksi) for 1345-A, about 57% more; tensile strength follows at 830 MPa (120 ksi) vs 725 MPa (105 ksi). In exchange, 1345-A is the more ductile: elongation 20% versus 12% for 1345-CD, and 1345-CD is harder (248 HB vs 205 HB). 1345-A runs hotter in service (400°C vs 300°C continuous).
1345-AChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
1345-CDChoose it when strength drives the design.
1345-A vs 1345-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 440 MPa63.8 ksi · Fracture Toughness (K_IC) 60 MPa·√m54.6 ksi·√in · Hardness, Vickers 215 HV
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 43 W/m·K24.8 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 60 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 1.9 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1345-A vs 1345-CD — frequently asked
Is 1345-CD stronger than 1345-A?
Yes. 1345-CD has a typical yield strength of 690 MPa (100 ksi) against 440 MPa (63.8 ksi) for 1345-A — about 57% more. Tensile strength is 830 MPa (120 ksi) vs 725 MPa (105 ksi).
Which condition does FabDigit quote by default, A or CD?
A is the default 1345 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1345-A or 1345-CD?
1345-CD, by a small margin. Both rate fair for machinability — 50/100 against 45/100 for 1345-A; for welding the order is 1345-A first (poor, 30/100) then 1345-CD (poor, 25/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1345-A and 1345-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.