Stainless Steel S44627 Cold Drawn vs S44627 Cold Rolled Annealed
Stainless Steel · S44627 temper comparison
S44627 Cold Drawn and S44627 Cold Rolled Annealed are two conditions of the same stainless steel grade, S44627: Cold Drawn versus Cold Rolled Annealed (2B/BA cold rolled sheet and strip). The chemistry is identical, so every difference below comes from the condition. S44627 Cold Drawn is the stronger of the two: yield strength 520 MPa (75.4 ksi) against 355 MPa (51.5 ksi) for S44627 Cold Rolled Annealed, about 46% more; tensile strength follows at 620 MPa (89.9 ksi) vs 500 MPa (72.5 ksi). In exchange, S44627 Cold Rolled Annealed is the more ductile: elongation 30% versus 15% for S44627 Cold Drawn, and S44627 Cold Drawn is harder (220 HB vs 165 HB).
S44627 Cold DrawnChoose it when strength drives the design.
S44627 Cold Rolled AnnealedChoose it when the part is bent, formed or impact-loaded.
S44627 Cold Drawn vs S44627 Cold Rolled Annealed: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
S44627 Cold DrawnS44627 Cold Rolled Annealed
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.67 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 17.5 W/m·K10.1 BTU/hr·ft·°F · Specific Heat Capacity 420 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 9.9 µm/m·K5.5 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Max Service Temperature (continuous) 315°C599 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.9 % IACS · Electrical Resistivity 6×10⁻⁷ Ω·m23.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Brazeability / Solderability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 52 MJ/kg22,356 BTU/lb · Embodied Carbon (primary production) 3.8 kg CO₂/kg · Embodied Water 120 L/kg14.4 gal/lb · Typical Recycled Content 55%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S44627 Cold Drawn vs S44627 Cold Rolled Annealed — frequently asked
Is S44627 Cold Drawn stronger than S44627 Cold Rolled Annealed?
Yes. S44627 Cold Drawn has a typical yield strength of 520 MPa (75.4 ksi) against 355 MPa (51.5 ksi) for S44627 Cold Rolled Annealed — about 46% more. Tensile strength is 620 MPa (89.9 ksi) vs 500 MPa (72.5 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Cold Rolled Annealed?
Annealed is the default S44627 condition in the FabDigit quote flow (neither Cold Drawn nor Cold Rolled Annealed). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, S44627 Cold Drawn or S44627 Cold Rolled Annealed?
S44627 Cold Rolled Annealed. Its weldability rates good (60/100) against good (55/100) for S44627 Cold Drawn.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S44627 Cold Drawn and S44627 Cold Rolled Annealed side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.