Stainless Steel S32520-CD vs S32520 CR+SA
Stainless Steel · S32520 temper comparison
S32520-CD and S32520 CR+SA are two conditions of the same stainless steel grade, S32520: CD (cold drawn) versus CR+SA (cold rolled sheet/strip, solution annealed and pickled). The chemistry is identical, so every difference below comes from the condition. S32520-CD is the stronger of the two: yield strength 780 MPa (113 ksi) against 640 MPa (92.8 ksi) for S32520 CR+SA, about 22% more; tensile strength follows at 950 MPa (138 ksi) vs 870 MPa (126 ksi). In exchange, S32520 CR+SA is the more ductile: elongation 28% versus 18% for S32520-CD, and S32520-CD is harder (300 HB vs 270 HB).
S32520-CDChoose it when strength drives the design.
S32520 CR+SAChoose it when the part is bent, formed or impact-loaded.
S32520-CD vs S32520 CR+SA: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,385°C2,525 °F · Liquidus Temperature 1,445°C2,633 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 17 W/m·K9.8 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.8 µm/m·K7.1 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2 % IACS · Electrical Resistivity 8.5×10⁻⁷ Ω·m33.5 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) 0.05 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 65 MJ/kg27,945 BTU/lb · Embodied Carbon (primary production) 4.8 kg CO₂/kg · Embodied Water 200 L/kg24 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S32520-CD vs S32520 CR+SA — frequently asked
Is S32520-CD stronger than S32520 CR+SA?
Yes. S32520-CD has a typical yield strength of 780 MPa (113 ksi) against 640 MPa (92.8 ksi) for S32520 CR+SA — about 22% more. Tensile strength is 950 MPa (138 ksi) vs 870 MPa (126 ksi).
Which condition does FabDigit quote by default, CD or CR+SA?
SA is the default S32520 condition in the FabDigit quote flow (neither CD nor CR+SA). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, S32520-CD or S32520 CR+SA?
S32520 CR+SA. Its weldability rates very good (70/100) against good (65/100) for S32520-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S32520-CD and S32520 CR+SA side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.