Stainless Steel Nitronic 50 Annealed vs Nitronic 50 Cold Drawn
Stainless Steel · Nitronic 50 temper comparison
Nitronic 50 Annealed and Nitronic 50 Cold Drawn are two conditions of the same stainless steel grade, Nitronic 50: Annealed versus Cold Drawn. The chemistry is identical, so every difference below comes from the condition. Nitronic 50 Cold Drawn is the stronger of the two: yield strength 760 MPa (110 ksi) against 430 MPa (62.4 ksi) for Nitronic 50 Annealed, about 77% more; tensile strength follows at 965 MPa (140 ksi) vs 780 MPa (113 ksi). In exchange, Nitronic 50 Annealed is the more ductile: elongation 45% versus 25% for Nitronic 50 Cold Drawn, and Nitronic 50 Cold Drawn is harder (300 HB vs 210 HB). On the shop floor, Nitronic 50 Annealed welds better (very good vs good).
Nitronic 50 AnnealedChoose it when the part is bent, formed or impact-loaded, or when it will be welded.
Nitronic 50 Cold DrawnChoose it when strength drives the design.
Nitronic 50 Annealed vs Nitronic 50 Cold Drawn: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Nitronic 50 AnnealedNitronic 50 Cold Drawn
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 196 GPa28.4 Msi · Shear Modulus 76 GPa11 Msi · Bulk Modulus 158 GPa22.9 Msi · Poisson's Ratio 0.29 · Shear Strength 520 MPa75.4 ksi · Fracture Toughness (K_IC) 200 MPa·√m182 ksi·√in · Hardness, Vickers 228 HV
Physical
Density and transition temperatures.
Same in both: Density 7.88 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,343°C2,449 °F · Liquidus Temperature 1,399°C2,550 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 12.5 W/m·K7.2 BTU/hr·ft·°F · Specific Heat Capacity 502 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 15.3 µm/m·K8.5 µin/in·°F · Max Service Temperature (continuous) 800°C1,472 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.4 % IACS · Electrical Resistivity 7.2×10⁻⁷ Ω·m28.3 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 78 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 72 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 62 MJ/kg26,655 BTU/lb · Embodied Carbon (primary production) 4.6 kg CO₂/kg · Embodied Water 250 L/kg30 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Nitronic 50 Annealed vs Nitronic 50 Cold Drawn — frequently asked
Is Nitronic 50 Cold Drawn stronger than Nitronic 50 Annealed?
Yes. Nitronic 50 Cold Drawn has a typical yield strength of 760 MPa (110 ksi) against 430 MPa (62.4 ksi) for Nitronic 50 Annealed — about 77% more. Tensile strength is 965 MPa (140 ksi) vs 780 MPa (113 ksi).
Which condition does FabDigit quote by default, Annealed or Cold Drawn?
Solution Annealed is the default Nitronic 50 condition in the FabDigit quote flow (neither Annealed nor Cold Drawn). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, Nitronic 50 Annealed or Nitronic 50 Cold Drawn?
Nitronic 50 Annealed. Its weldability rates very good (70/100) against good (60/100) for Nitronic 50 Cold Drawn.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Nitronic 50 Annealed and Nitronic 50 Cold Drawn side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.