Stainless Steel Custom 465-H1100 vs Custom 465-H1150
Stainless Steel · Custom 465 temper comparison
Custom 465-H1100 and Custom 465-H1150 are two conditions of the same stainless steel grade, Custom 465: H1100 (aged 593 °C (1100 °F) for 4 h) versus H1150 (overaged 621 °C (1150 °F) for 4 h, maximum toughness). The chemistry is identical, so every difference below comes from the condition. Custom 465-H1100 is the stronger of the two: yield strength 1,310 MPa (190 ksi) against 1,170 MPa (170 ksi) for Custom 465-H1150, about 12% more; tensile strength follows at 1,400 MPa (203 ksi) vs 1,275 MPa (185 ksi). Custom 465-H1100 is harder — 43 HRC against 40 HRC for Custom 465-H1150 — which matters for wear surfaces and threads.
Custom 465-H1100Choose it when strength drives the design, or when surface hardness matters.
Custom 465-H1100 vs Custom 465-H1150: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Custom 465-H1100Custom 465-H1150
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.78 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,440°C2,624 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.4 µm/m·K5.8 µin/in·°F · Min Service Temperature -75°C-103 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.15 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 85 MJ/kg36,543 BTU/lb · Embodied Carbon (primary production) 5.6 kg CO₂/kg · Embodied Water 250 L/kg30 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Custom 465-H1100 vs Custom 465-H1150 — frequently asked
Is Custom 465-H1100 stronger than Custom 465-H1150?
Yes. Custom 465-H1100 has a typical yield strength of 1,310 MPa (190 ksi) against 1,170 MPa (170 ksi) for Custom 465-H1150 — about 12% more. Tensile strength is 1,400 MPa (203 ksi) vs 1,275 MPa (185 ksi).
Which condition does FabDigit quote by default, H1100 or H1150?
Condition A is the default Custom 465 condition in the FabDigit quote flow (neither H1100 nor H1150). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose Custom 465-H1100 over Custom 465-H1150?
Pick Custom 465-H1100 when strength drives the design, or when surface hardness matters.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Custom 465-H1100 and Custom 465-H1150 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.