Stainless Steel 317LN Cold Drawn vs 317LN Full Hard
Stainless Steel · 317LN temper comparison
317LN Cold Drawn and 317LN Full Hard are two conditions of the same stainless steel grade, 317LN: Cold Drawn versus Full Hard. The chemistry is identical, so every difference below comes from the condition. 317LN Full Hard is the stronger of the two: yield strength 1,000 MPa (145 ksi) against 500 MPa (72.5 ksi) for 317LN Cold Drawn, about 100% more; tensile strength follows at 1,280 MPa (186 ksi) vs 720 MPa (104 ksi). In exchange, 317LN Cold Drawn is the more ductile: elongation 30% versus 6% for 317LN Full Hard, and 317LN Full Hard is harder (370 HB vs 220 HB). 317LN Cold Drawn runs hotter in service (400°C vs 300°C continuous). On the shop floor, 317LN Cold Drawn machines more easily (fair vs poor) and 317LN Cold Drawn welds better (very good vs good).
317LN Cold DrawnChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
317LN Full HardChoose it when strength drives the design.
317LN Cold Drawn vs 317LN Full Hard: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
317LN Cold Drawn317LN Full Hard
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 166 GPa24.1 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.98 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,375°C2,507 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 14.5 W/m·K8.4 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 16 µm/m·K8.9 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.2 % IACS · Electrical Resistivity 7.9×10⁻⁷ Ω·m31.1 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.05 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 60 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 60 MJ/kg25,795 BTU/lb · Embodied Carbon (primary production) 4.5 kg CO₂/kg · Embodied Water 180 L/kg21.6 gal/lb · Typical Recycled Content 65%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
317LN Cold Drawn vs 317LN Full Hard — frequently asked
Is 317LN Full Hard stronger than 317LN Cold Drawn?
Yes. 317LN Full Hard has a typical yield strength of 1,000 MPa (145 ksi) against 500 MPa (72.5 ksi) for 317LN Cold Drawn — about 100% more. Tensile strength is 1,280 MPa (186 ksi) vs 720 MPa (104 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Full Hard?
Annealed is the default 317LN condition in the FabDigit quote flow (neither Cold Drawn nor Full Hard). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 317LN Cold Drawn or 317LN Full Hard?
317LN Cold Drawn. Its machinability rates fair (38/100) against poor (25/100) for 317LN Full Hard; for welding the order is 317LN Cold Drawn first (very good, 82/100) then 317LN Full Hard (good, 60/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 317LN Cold Drawn and 317LN Full Hard side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.