Stainless Steel 1.4848 vs 1.4874
Stainless Steel · grade comparison
Stainless Steel 1.4848 and 1.4874 are both stainless steel grades. 1.4874 is the stronger of the two: yield strength 300 MPa (43.5 ksi) against 280 MPa (40.6 ksi) for 1.4848, about 7% more; tensile strength follows at 560 MPa (81.2 ksi) vs 530 MPa (76.9 ksi). In exchange, 1.4848 is the more ductile: elongation 14% versus 6% for 1.4874, and 1.4874 is harder (225 HB vs 190 HB). 1.4848 runs hotter in service (1,100°C vs 1,000°C continuous). On the shop floor, 1.4848 welds better (fair vs poor) and 1.4848 sits in a lower cost tier (premium, $$$) than 1.4874 (high, $$$$).
1.4848Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
1.4874Choose it when strength drives the design.
1.4848 vs 1.4874: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Compressive Strength
Fracture Toughness (K_IC)
Hardness, Rockwell C
Same in both: Fatigue Strength (Endurance Limit) 200 MPa29 ksi
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 14 W/m·K8.1 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Same in both: Thermal Shock Resistance Index 3
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 1.4848 | 1.4874 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$ Premium | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 7 finishes: Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Pickling, Plasma Spray, Silver Plating.
1.4848 vs 1.4874 — frequently asked
Is 1.4874 stronger than 1.4848?
Yes. 1.4874 has a typical yield strength of 300 MPa (43.5 ksi) against 280 MPa (40.6 ksi) for 1.4848 — about 7% more. Tensile strength is 560 MPa (81.2 ksi) vs 530 MPa (76.9 ksi).
Which is cheaper, 1.4848 or 1.4874?
1.4848 is the lower-cost material: it sits in the premium tier ($$$) while 1.4874 is high ($$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, 1.4848 or 1.4874?
1.4848, by a small margin. Both rate poor for machinability — 25/100 against 18/100 for 1.4874; for welding the order is 1.4848 first (fair, 45/100) then 1.4874 (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4848 and 1.4874 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.