Stainless Steel 1.4762 Annealed vs 1.4762-CD
Stainless Steel · 1.4762 temper comparison
1.4762 Annealed and 1.4762-CD are two conditions of the same stainless steel grade, 1.4762: Annealed versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. 1.4762-CD is the stronger of the two: yield strength 500 MPa (72.5 ksi) against 330 MPa (47.9 ksi) for 1.4762 Annealed, about 52% more; tensile strength follows at 680 MPa (98.6 ksi) vs 580 MPa (84.1 ksi). In exchange, 1.4762 Annealed is the more ductile: elongation 18% versus 12% for 1.4762-CD, and 1.4762-CD is harder (230 HB vs 195 HB).
1.4762 AnnealedChoose it when the part is bent, formed or impact-loaded.
1.4762-CDChoose it when strength drives the design.
1.4762 Annealed vs 1.4762-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.15 g/cm³0.26 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 17 W/m·K9.8 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.5 µm/m·K5.8 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Max Service Temperature (continuous) 1,150°C2,102 °F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.6 % IACS · Electrical Resistivity 1.05×10⁻⁶ Ω·m41.3 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V · Corrosion Resistance 55 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 35 / 100 · Brazeability / Solderability 40 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 45 MJ/kg19,347 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 120 L/kg14.4 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4762 Annealed vs 1.4762-CD — frequently asked
Is 1.4762-CD stronger than 1.4762 Annealed?
Yes. 1.4762-CD has a typical yield strength of 500 MPa (72.5 ksi) against 330 MPa (47.9 ksi) for 1.4762 Annealed — about 52% more. Tensile strength is 680 MPa (98.6 ksi) vs 580 MPa (84.1 ksi).
Which condition does FabDigit quote by default, Annealed or CD?
Annealed is the default 1.4762 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1.4762 Annealed or 1.4762-CD?
1.4762-CD, by a small margin. Both rate fair for machinability — 45/100 against 40/100 for 1.4762 Annealed.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4762 Annealed and 1.4762-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.