Stainless Steel 1.4630 2H vs 1.4630-CD
Stainless Steel · 1.4630 temper comparison
1.4630 2H and 1.4630-CD are two conditions of the same stainless steel grade, 1.4630: 2H (cold worked / temper rolled) versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. 1.4630-CD is the stronger of the two: yield strength 500 MPa (72.5 ksi) against 460 MPa (66.7 ksi) for 1.4630 2H, about 9% more; tensile strength follows at 600 MPa (87 ksi) vs 560 MPa (81.2 ksi). In exchange, 1.4630 2H is the more ductile: elongation 14% versus 12% for 1.4630-CD. 1.4630-CD runs hotter in service (500°C vs 400°C continuous).
1.4630 2HChoose it when the part is bent, formed or impact-loaded.
1.4630-CDChoose it when strength drives the design, or when the part sees heat.
1.4630 2H vs 1.4630-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 220 GPa31.9 Msi · Shear Modulus 85 GPa12.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.28 · Reduction in Area 45%
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 24 W/m·K13.9 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.5 µm/m·K5.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 2.6 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Formability (cold)
Same in both: Machinability 60 / 100 · Machinability Rating (AISI 1212 = 100 %) 60% · Weldability 75 / 100 · Brazeability / Solderability 65 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 70%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4630 2H vs 1.4630-CD — frequently asked
Is 1.4630-CD stronger than 1.4630 2H?
Yes. 1.4630-CD has a typical yield strength of 500 MPa (72.5 ksi) against 460 MPa (66.7 ksi) for 1.4630 2H — about 9% more. Tensile strength is 600 MPa (87 ksi) vs 560 MPa (81.2 ksi).
Which condition does FabDigit quote by default, 2H or CD?
A is the default 1.4630 condition in the FabDigit quote flow (neither 2H nor CD). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 1.4630 2H over 1.4630-CD?
Pick 1.4630 2H when the part is bent, formed or impact-loaded. Pick 1.4630-CD when strength drives the design, or when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4630 2H and 1.4630-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.