Stainless Steel 1.4511 Annealed vs 1.4511 Cold Drawn
Stainless Steel · 1.4511 temper comparison
1.4511 Annealed and 1.4511 Cold Drawn are two conditions of the same stainless steel grade, 1.4511: Annealed versus Cold Drawn. The chemistry is identical, so every difference below comes from the condition. 1.4511 Cold Drawn is the stronger of the two: yield strength 480 MPa (69.6 ksi) against 300 MPa (43.5 ksi) for 1.4511 Annealed, about 60% more; tensile strength follows at 600 MPa (87 ksi) vs 470 MPa (68.2 ksi). In exchange, 1.4511 Annealed is the more ductile: elongation 30% versus 15% for 1.4511 Cold Drawn, and 1.4511 Cold Drawn is harder (195 HB vs 165 HB).
1.4511 AnnealedChoose it when the part is bent, formed or impact-loaded.
1.4511 Cold DrawnChoose it when strength drives the design.
1.4511 Annealed vs 1.4511 Cold Drawn: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
1.4511 Annealed1.4511 Cold Drawn
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 220 GPa31.9 Msi · Shear Modulus 85 GPa12.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 25 W/m·K14.4 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10 µm/m·K5.6 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Max Service Temperature (continuous) 815°C1,499 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.9 % IACS · Electrical Resistivity 6×10⁻⁷ Ω·m23.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 62 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 47 MJ/kg20,206 BTU/lb · Embodied Carbon (primary production) 3 kg CO₂/kg · Embodied Water 110 L/kg13.2 gal/lb · Typical Recycled Content 65%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4511 Annealed vs 1.4511 Cold Drawn — frequently asked
Is 1.4511 Cold Drawn stronger than 1.4511 Annealed?
Yes. 1.4511 Cold Drawn has a typical yield strength of 480 MPa (69.6 ksi) against 300 MPa (43.5 ksi) for 1.4511 Annealed — about 60% more. Tensile strength is 600 MPa (87 ksi) vs 470 MPa (68.2 ksi).
Which condition does FabDigit quote by default, Annealed or Cold Drawn?
Annealed is the default 1.4511 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 1.4511 Annealed over 1.4511 Cold Drawn?
Pick 1.4511 Annealed when the part is bent, formed or impact-loaded. Pick 1.4511 Cold Drawn when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4511 Annealed and 1.4511 Cold Drawn side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.