Solder & Low-Melting Alloy Pb60Sn40 vs Pb74Sn25Sb1
Solder & Low-Melting Alloy · grade comparison
Solder & Low-Melting Alloy Pb60Sn40 and Pb74Sn25Sb1 are both solder & low-melting alloy grades. Pb60Sn40 is the stronger of the two: yield strength 24 MPa (3.48 ksi) against 22 MPa (3.19 ksi) for Pb74Sn25Sb1, about 9% more; tensile strength follows at 38 MPa (5.51 ksi) vs 34 MPa (4.93 ksi). Pb60Sn40 is the more ductile: elongation 40% versus 35% for Pb74Sn25Sb1. Pb60Sn40 is lighter (9.29 g/cm³ vs 9.96 g/cm³ for Pb74Sn25Sb1) and Pb60Sn40 conducts electricity better (10.1 % IACS vs 9 % IACS). On the shop floor, Pb60Sn40 welds better (poor vs not recommended).
Pb60Sn40Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Pb60Sn40 vs Pb74Sn25Sb1: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all solder & low-melting alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all solder & low-melting alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Same in both: Shear Modulus 9 GPa1.3 Msi · Poisson's Ratio 0.4 · Hardness, Brinell 12 HB
Physical
Density and transition temperatures.
Density
Liquidus Temperature
Same in both: Melting Point (Solidus) 183°C361 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Same in both: Max Service Temperature (continuous) 100°C212 °F · Min Service Temperature -55°C-67 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Castability
Brazeability / Solderability
Polishability
Same in both: Formability (cold) 90 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Same in both: Embodied Water 300 L/kg35.9 gal/lb
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every solder & low-melting alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Pb60Sn40 | Pb74Sn25Sb1 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Pb60Sn40 vs Pb74Sn25Sb1 — frequently asked
Is Pb60Sn40 stronger than Pb74Sn25Sb1?
Yes. Pb60Sn40 has a typical yield strength of 24 MPa (3.48 ksi) against 22 MPa (3.19 ksi) for Pb74Sn25Sb1 — about 9% more. Tensile strength is 38 MPa (5.51 ksi) vs 34 MPa (4.93 ksi).
Which is cheaper, Pb60Sn40 or Pb74Sn25Sb1?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, Pb60Sn40 or Pb74Sn25Sb1?
Pb74Sn25Sb1. Its machinability rates fair (35/100) against poor (30/100) for Pb60Sn40; for welding the order is Pb60Sn40 first (poor, 20/100) then Pb74Sn25Sb1 (not recommended, 10/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Pb60Sn40 and Pb74Sn25Sb1 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.