Solder & Low-Melting Alloy B560 Type III Cold Rolled vs B560 Type III F-Cast
Solder & Low-Melting Alloy · B560 Type III temper comparison
B560 Type III Cold Rolled and B560 Type III F-Cast are two conditions of the same solder & low-melting alloy grade, B560 Type III: Cold Rolled versus F-Cast (f). The chemistry is identical, so every difference below comes from the condition. B560 Type III Cold Rolled is the stronger of the two: yield strength 34 MPa (4.93 ksi) against 22 MPa (3.19 ksi) for B560 Type III F-Cast, about 55% more; tensile strength follows at 52 MPa (7.54 ksi) vs 38 MPa (5.51 ksi). In exchange, B560 Type III F-Cast is the more ductile: elongation 30% versus 25% for B560 Type III Cold Rolled, and B560 Type III Cold Rolled is harder (21 HB vs 15 HB). B560 Type III F-Cast runs hotter in service (90°C vs 75°C continuous). On the shop floor, B560 Type III Cold Rolled machines more easily (80 vs 70 out of 100).
B560 Type III Cold RolledChoose it when strength drives the design, or when the part is machined in volume.
B560 Type III F-CastChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
B560 Type III Cold Rolled vs B560 Type III F-Cast: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all solder & low-melting alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all solder & low-melting alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
B560 Type III Cold RolledB560 Type III F-Cast
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Hardness, Brinell
Same in both: Shear Modulus 17 GPa2.5 Msi · Bulk Modulus 56 GPa8.1 Msi · Poisson's Ratio 0.36
Physical
Density and transition temperatures.
Same in both: Density 7.3 g/cm³0.26 lb/in³ · Melting Point (Solidus) 235°C455 °F · Liquidus Temperature 260°C500 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 220 J/kg·K0.05 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23 µm/m·K12.8 µin/in·°F · Latent Heat of Fusion 59 J/g25.4 BTU/lb · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.5 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 38 / 100 · Castability 85 / 100 · Brazeability / Solderability 95 / 100 · Polishability 88 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 260 MJ/kg111,780 BTU/lb · Embodied Carbon (primary production) 17 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every solder & low-melting alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
B560 Type III Cold Rolled vs B560 Type III F-Cast — frequently asked
Is B560 Type III Cold Rolled stronger than B560 Type III F-Cast?
Yes. B560 Type III Cold Rolled has a typical yield strength of 34 MPa (4.93 ksi) against 22 MPa (3.19 ksi) for B560 Type III F-Cast — about 55% more. Tensile strength is 52 MPa (7.54 ksi) vs 38 MPa (5.51 ksi).
Which condition does FabDigit quote by default, Cold Rolled or F-Cast?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, B560 Type III Cold Rolled or B560 Type III F-Cast?
B560 Type III Cold Rolled, by a small margin. Both rate very good for machinability — 80/100 against 70/100 for B560 Type III F-Cast.
Ready to make it?
Upload a CAD file and FabDigit prices the part in B560 Type III Cold Rolled and B560 Type III F-Cast side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.