Precious Metal BAg-9-ANN vs BAg-9 Hard
Precious Metal · BAg-9 temper comparison
BAg-9-ANN and BAg-9 Hard are two conditions of the same precious metal grade, BAg-9: ANN (annealed) versus Hard (cold drawn / hard temper wire and strip). The chemistry is identical, so every difference below comes from the condition. BAg-9 Hard is the stronger of the two: yield strength 520 MPa (75.4 ksi) against 170 MPa (24.7 ksi) for BAg-9-ANN, about 3.1 times as much; tensile strength follows at 620 MPa (89.9 ksi) vs 380 MPa (55.1 ksi). In exchange, BAg-9-ANN is the more ductile: elongation 32% versus 4% for BAg-9 Hard, and BAg-9 Hard is harder (155 HB vs 85 HB). BAg-9-ANN runs hotter in service (200°C vs 150°C continuous). On the shop floor, BAg-9 Hard machines more easily (50 vs 40 out of 100).
BAg-9-ANNChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
BAg-9 HardChoose it when strength drives the design, or when the part is machined in volume.
BAg-9-ANN vs BAg-9 Hard: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 85 GPa12.3 Msi · Shear Modulus 31 GPa4.5 Msi · Bulk Modulus 100 GPa14.5 Msi · Poisson's Ratio 0.36
Physical
Density and transition temperatures.
Same in both: Density 9.8 g/cm³0.35 lb/in³ · Melting Point (Solidus) 671°C1,240 °F · Liquidus Temperature 718°C1,324 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 255 J/kg·K0.06 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 19 µm/m·K10.6 µin/in·°F · Latent Heat of Fusion 100 J/g43 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) 0 V · Corrosion Resistance 82 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 30 / 100 · Castability 80 / 100 · Brazeability / Solderability 96 / 100 · Polishability 90 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 1,100 MJ/kg472,915 BTU/lb · Embodied Carbon (primary production) 70 kg CO₂/kg · Embodied Water 2,500 L/kg300 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every precious metal grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
BAg-9-ANN vs BAg-9 Hard — frequently asked
Is BAg-9 Hard stronger than BAg-9-ANN?
Yes. BAg-9 Hard has a typical yield strength of 520 MPa (75.4 ksi) against 170 MPa (24.7 ksi) for BAg-9-ANN — about 3.1 times as much. Tensile strength is 620 MPa (89.9 ksi) vs 380 MPa (55.1 ksi).
Which condition does FabDigit quote by default, ANN or Hard?
ANN is the default BAg-9 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, BAg-9-ANN or BAg-9 Hard?
BAg-9 Hard, by a small margin. Both rate fair for machinability — 50/100 against 40/100 for BAg-9-ANN.
Ready to make it?
Upload a CAD file and FabDigit prices the part in BAg-9-ANN and BAg-9 Hard side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.