Precious Metal BAg-8 Annealed vs BAg-8 AS-BRAZED
Precious Metal · BAg-8 temper comparison
BAg-8 Annealed and BAg-8 AS-BRAZED are two conditions of the same precious metal grade, BAg-8: Annealed versus AS-BRAZED. The chemistry is identical, so every difference below comes from the condition. BAg-8 Annealed is the stronger of the two: yield strength 160 MPa (23.2 ksi) against 140 MPa (20.3 ksi) for BAg-8 AS-BRAZED, about 14% more; tensile strength follows at 380 MPa (55.1 ksi) vs 330 MPa (47.9 ksi). BAg-8 Annealed is the more ductile: elongation 20% versus 12% for BAg-8 AS-BRAZED, and BAg-8 AS-BRAZED is harder (84 HB vs 65 HB).
BAg-8 AnnealedChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
BAg-8 Annealed vs BAg-8 AS-BRAZED: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 90 GPa13.1 Msi · Shear Modulus 34 GPa4.9 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.36
Physical
Density and transition temperatures.
Same in both: Density 10 g/cm³0.36 lb/in³ · Melting Point (Solidus) 780°C1,436 °F · Liquidus Temperature 780°C1,436 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 355 W/m·K205 BTU/hr·ft·°F · Specific Heat Capacity 235 J/kg·K0.06 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 19.6 µm/m·K10.9 µin/in·°F · Latent Heat of Fusion 130 J/g55.9 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) 0 V · Corrosion Resistance 72 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 30 / 100 · Castability 92 / 100 · Brazeability / Solderability 98 / 100 · Polishability 85 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 1,100 MJ/kg472,915 BTU/lb · Embodied Carbon (primary production) 78 kg CO₂/kg · Embodied Water 2,500 L/kg300 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every precious metal grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
BAg-8 Annealed vs BAg-8 AS-BRAZED — frequently asked
Is BAg-8 Annealed stronger than BAg-8 AS-BRAZED?
Yes. BAg-8 Annealed has a typical yield strength of 160 MPa (23.2 ksi) against 140 MPa (20.3 ksi) for BAg-8 AS-BRAZED — about 14% more. Tensile strength is 380 MPa (55.1 ksi) vs 330 MPa (47.9 ksi).
Which condition does FabDigit quote by default, Annealed or AS-BRAZED?
Annealed is the default BAg-8 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, BAg-8 Annealed or BAg-8 AS-BRAZED?
BAg-8 Annealed. Its machinability rates good (55/100) against fair (50/100) for BAg-8 AS-BRAZED.
Ready to make it?
Upload a CAD file and FabDigit prices the part in BAg-8 Annealed and BAg-8 AS-BRAZED side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.