PEEK-450G CF30 vs PEEK-450G FC30
Polymer · PEEK-450G grade comparison
PEEK-450G CF30 and PEEK-450G FC30 are two grades of the same polymer grade, PEEK-450G: CF30 (450CA30) versus FC30 (450FC30). The chemistry is identical, so every difference below comes from the condition. PEEK-450G CF30 is the stronger of the two: tensile strength 224 MPa (32.5 ksi) against 130 MPa (18.9 ksi) for PEEK-450G FC30, about 72% more. In exchange, PEEK-450G FC30 is the more ductile: elongation 2.5% versus 1.8% for PEEK-450G CF30. PEEK-450G CF30 is stiffer (23 GPa vs 12 GPa). On the shop floor, PEEK-450G FC30 machines more easily (good vs fair).
PEEK-450G CF30Choose it when strength drives the design.
PEEK-450G FC30Choose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
PEEK-450G CF30 vs PEEK-450G FC30: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Rockwell M
Same in both: Shear Modulus 1.4 GPa0.2 Msi · Bulk Modulus 5 GPa0.73 Msi · Poisson's Ratio 0.38 · Yield Strength (0.2% offset) 100 MPa14.5 ksi · Compressive Modulus 3.5 GPa0.51 Msi · Shear Strength 55 MPa8 ksi · Fracture Toughness (K_IC) 6.5 MPa·√m5.9 ksi·√in · Hardness, Shore D 85 Shore D · Hardness, Rockwell R 126 HRR
Physical
Density and transition temperatures.
Density
Same in both: Melting Temperature (Tm) 343°C649 °F · Glass Transition (Tg) 143°C289 °F · Water Absorption (24 h) 0.12% · Water Absorption (Saturation) 0.45% · Refractive Index 1.65
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Heat Deflection Temp. @ 1.8 MPa
Same in both: Specific Heat Capacity 1,340 J/kg·K0.32 BTU/lb·°F · Max Service Temperature (continuous) 260°C500 °F · Min Service Temperature -60°C-76 °F · Heat Deflection Temp. @ 0.45 MPa 290°C554 °F · Limiting Oxygen Index 35% · Max Service Temperature (short-term) 310°C590 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Volume Resistivity
Same in both: Dielectric Strength 20 kV/mm508 V/mil · Dielectric Constant (1 MHz) 3.2 · Dissipation Factor (1 MHz) 0.003 · Surface Resistivity 1×10¹⁶ Ω · Comparative Tracking Index (CTI) 150 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
UV / Weathering Resistance
Same in both: Corrosion Resistance 92 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Mold Shrinkage
Same in both: Weldability 55 / 100 · Formability (cold) 35 / 100 · Polishability 70 / 100 · Melt Flow Rate 3 g/10 min · Processing Melt Temperature (typ.) 380°C716 °F · Mold Temperature (typ.) 190°C374 °F
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 290 MJ/kg124,678 BTU/lb · Embodied Carbon (primary production) 16 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 0%
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
PEEK-450G CF30 vs PEEK-450G FC30 — frequently asked
Is PEEK-450G CF30 stronger than PEEK-450G FC30?
Yes. PEEK-450G CF30 has a typical tensile strength of 224 MPa (32.5 ksi) against 130 MPa (18.9 ksi) for PEEK-450G FC30 — about 72% more.
Which grade does FabDigit quote by default, CF30 or FC30?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, PEEK-450G CF30 or PEEK-450G FC30?
PEEK-450G FC30. Its machinability rates good (55/100) against fair (35/100) for PEEK-450G CF30.
Ready to make it?
Upload a CAD file and FabDigit prices the part in PEEK-450G CF30 and PEEK-450G FC30 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.