PC/PET GF30 vs PC/PET PCR
Polymer · PC/PET grade comparison
PC/PET GF30 and PC/PET PCR are two grades of the same polymer grade, PC/PET: GF30 (30 % glass-fiber reinforced) versus PCR (PCR / recycled-content grade). The chemistry is identical, so every difference below comes from the condition. PC/PET GF30 is the stronger of the two: yield strength 53 MPa (7.69 ksi) against 50 MPa (7.25 ksi) for PC/PET PCR, about 6% more; tensile strength follows at 115 MPa (16.7 ksi) vs 52 MPa (7.54 ksi). In exchange, PC/PET PCR is the more ductile: elongation 90% versus 3.5% for PC/PET GF30. PC/PET PCR is lighter (1.22 g/cm³ vs 1.43 g/cm³ for PC/PET GF30) and PC/PET GF30 is stiffer (7.5 GPa vs 2.1 GPa). On the shop floor, PC/PET PCR machines more easily (good vs fair).
PC/PET GF30Choose it when strength drives the design.
PC/PET PCRChoose it when the part is bent, formed or impact-loaded, or when weight is the constraint.
PC/PET GF30 vs PC/PET PCR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Rockwell M
Hardness, Rockwell R
Same in both: Poisson's Ratio 0.4
Physical
Density and transition temperatures.
Density
Same in both: Melting Temperature (Tm) 250°C482 °F · Glass Transition (Tg) 140°C284 °F · Water Absorption (24 h) 0.15% · Water Absorption (Saturation) 0.4%
Thermal
How each material carries heat and how hot it can run.
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Vicat Softening Point (B50)
Limiting Oxygen Index
Same in both: Thermal Conductivity 0.21 W/m·K0.12 BTU/hr·ft·°F · Specific Heat Capacity 1,300 J/kg·K0.31 BTU/lb·°F · Min Service Temperature -40°C-40 °F · Max Service Temperature (short-term) 130°C266 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Resistivity 1×10¹⁴ Ω·m3.94×10²¹ µΩ·in · Dielectric Strength 22 kV/mm559 V/mil · Dielectric Constant (1 MHz) 3.1 · Dissipation Factor (1 MHz) 0.012 · Volume Resistivity 1×10¹⁶ Ω·cm · Surface Resistivity 1×10¹⁶ Ω · Comparative Tracking Index (CTI) 250 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: UV / Weathering Resistance 35 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Mold Shrinkage
Melt Flow Rate
Same in both: Polishability 55 / 100 · Processing Melt Temperature (typ.) 265°C509 °F · Mold Temperature (typ.) 75°C167 °F
Sustainability
Primary-production footprint per kilogram.
Embodied Carbon (primary production)
Typical Recycled Content
Same in both: Embodied Energy (primary production) 105 MJ/kg45,142 BTU/lb · Embodied Water 300 L/kg35.9 gal/lb
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
PC/PET GF30 vs PC/PET PCR — frequently asked
Is PC/PET GF30 stronger than PC/PET PCR?
Yes. PC/PET GF30 has a typical yield strength of 53 MPa (7.69 ksi) against 50 MPa (7.25 ksi) for PC/PET PCR — about 6% more. Tensile strength is 115 MPa (16.7 ksi) vs 52 MPa (7.54 ksi).
Which grade does FabDigit quote by default, GF30 or PCR?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, PC/PET GF30 or PC/PET PCR?
PC/PET PCR. Its machinability rates good (60/100) against fair (45/100) for PC/PET GF30.
Ready to make it?
Upload a CAD file and FabDigit prices the part in PC/PET GF30 and PC/PET PCR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.