PA10T GF30 vs PA10T GF50
Polymer · PA10T grade comparison
PA10T GF30 and PA10T GF50 are two grades of the same polymer grade, PA10T: GF30 (30 % glass-fiber reinforced) versus GF50 (50 % glass-fiber reinforced). The chemistry is identical, so every difference below comes from the condition. PA10T GF50 is the stronger of the two: tensile strength 230 MPa (33.4 ksi) against 190 MPa (27.6 ksi) for PA10T GF30, about 21% more. In exchange, PA10T GF30 is the more ductile: elongation 2.5% versus 1.8% for PA10T GF50. PA10T GF30 is lighter (1.35 g/cm³ vs 1.58 g/cm³ for PA10T GF50) and PA10T GF50 is stiffer (17 GPa vs 10 GPa). On the shop floor, PA10T GF30 machines more easily (fair vs poor).
PA10T GF30Choose it when the part is bent, formed or impact-loaded, or when weight is the constraint.
PA10T GF50Choose it when strength drives the design.
PA10T GF30 vs PA10T GF50: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Rockwell M
Same in both: Poisson's Ratio 0.4 · Yield Strength (0.2% offset) 90 MPa13.1 ksi · Compressive Strength 90 MPa13.1 ksi · Hardness, Shore D 82 Shore D
Physical
Density and transition temperatures.
Density
Water Absorption (24 h)
Water Absorption (Saturation)
Same in both: Melting Temperature (Tm) 316°C601 °F · Glass Transition (Tg) 125°C257 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Max Service Temperature (short-term)
Same in both: Specific Heat Capacity 1,500 J/kg·K0.36 BTU/lb·°F · Min Service Temperature -40°C-40 °F · Vicat Softening Point (B50) 250°C482 °F · Limiting Oxygen Index 25%
Electrical
Conductivity and insulation.
Same in both: Electrical Resistivity 1×10¹³ Ω·m3.94×10²⁰ µΩ·in · Dielectric Strength 28 kV/mm711 V/mil · Dielectric Constant (1 MHz) 3.6 · Dissipation Factor (1 MHz) 0.02 · Volume Resistivity 1×10¹⁵ Ω·cm · Surface Resistivity 1×10¹⁵ Ω · Comparative Tracking Index (CTI) 600 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 80 / 100 · UV / Weathering Resistance 40 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Mold Shrinkage
Same in both: Weldability 55 / 100 · Formability (cold) 30 / 100 · Polishability 55 / 100 · Processing Melt Temperature (typ.) 325°C617 °F · Mold Temperature (typ.) 135°C275 °F
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 100 MJ/kg42,992 BTU/lb · Embodied Carbon (primary production) 5 kg CO₂/kg · Typical Recycled Content 0%
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
PA10T GF30 vs PA10T GF50 — frequently asked
Is PA10T GF50 stronger than PA10T GF30?
Yes. PA10T GF50 has a typical tensile strength of 230 MPa (33.4 ksi) against 190 MPa (27.6 ksi) for PA10T GF30 — about 21% more.
Which grade does FabDigit quote by default, GF30 or GF50?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, PA10T GF30 or PA10T GF50?
PA10T GF30. Its machinability rates fair (40/100) against poor (30/100) for PA10T GF50.
Ready to make it?
Upload a CAD file and FabDigit prices the part in PA10T GF30 and PA10T GF50 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.