Laperos GF30 vs Laperos LD-RF
Polymer · Laperos grade comparison
Laperos GF30 and Laperos LD-RF are two grades of the same polymer grade, Laperos: GF30 (30% glass-fiber reinforced) versus LD-RF (low-dielectric / high-frequency grade). The chemistry is identical, so every difference below comes from the condition. Laperos GF30 is the stronger of the two: tensile strength 165 MPa (23.9 ksi) against 150 MPa (21.8 ksi) for Laperos LD-RF, about 10% more. Laperos GF30 is the more ductile: elongation 2.5% versus 2% for Laperos LD-RF. Laperos LD-RF is lighter (1.55 g/cm³ vs 1.61 g/cm³ for Laperos GF30) and Laperos GF30 is stiffer (14 GPa vs 12 GPa).
Laperos GF30Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Laperos LD-RFChoose it when weight is the constraint.
Laperos GF30 vs Laperos LD-RF: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Shore D
Hardness, Rockwell M
Same in both: Shear Modulus 3 GPa0.44 Msi · Poisson's Ratio 0.35
Physical
Density and transition temperatures.
Density
Same in both: Melting Temperature (Tm) 280°C536 °F · Glass Transition (Tg) 120°C248 °F · Water Absorption (24 h) 0.02% · Water Absorption (Saturation) 0.06%
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Heat Deflection Temp. @ 1.8 MPa
Limiting Oxygen Index
Same in both: Specific Heat Capacity 1,050 J/kg·K0.25 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8 µm/m·K4.4 µin/in·°F · Max Service Temperature (continuous) 220°C428 °F · Min Service Temperature -50°C-58 °F · Heat Deflection Temp. @ 0.45 MPa 265°C509 °F · Max Service Temperature (short-term) 280°C536 °F
Electrical
Conductivity and insulation.
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Same in both: Electrical Resistivity 1×10¹⁴ Ω·m3.94×10²¹ µΩ·in · Dielectric Strength 35 kV/mm889 V/mil · Volume Resistivity 1×10¹⁶ Ω·cm · Surface Resistivity 1×10¹⁶ Ω · Comparative Tracking Index (CTI) 200 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 90 / 100 · UV / Weathering Resistance 50 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Mold Shrinkage
Same in both: Weldability 25 / 100 · Formability (cold) 15 / 100 · Polishability 35 / 100 · Processing Melt Temperature (typ.) 310°C590 °F · Mold Temperature (typ.) 100°C212 °F
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 190 MJ/kg81,685 BTU/lb · Embodied Carbon (primary production) 9 kg CO₂/kg · Typical Recycled Content 0%
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Laperos GF30 vs Laperos LD-RF — frequently asked
Is Laperos GF30 stronger than Laperos LD-RF?
Yes. Laperos GF30 has a typical tensile strength of 165 MPa (23.9 ksi) against 150 MPa (21.8 ksi) for Laperos LD-RF — about 10% more.
Which grade does FabDigit quote by default, GF30 or LD-RF?
GF30 is the default Laperos condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose Laperos GF30 over Laperos LD-RF?
Pick Laperos GF30 when strength drives the design, or when the part is bent, formed or impact-loaded. Pick Laperos LD-RF when weight is the constraint.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Laperos GF30 and Laperos LD-RF side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.