Nickel Alloy NiCo20Cr20MoTi-CD vs NiCo20Cr20MoTi-ST
Nickel Alloy · NiCo20Cr20MoTi temper comparison
NiCo20Cr20MoTi-CD and NiCo20Cr20MoTi-ST are two conditions of the same nickel alloy grade, NiCo20Cr20MoTi: CD (cold drawn) versus ST (solution annealed). The chemistry is identical, so every difference below comes from the condition. NiCo20Cr20MoTi-CD is the stronger of the two: yield strength 800 MPa (116 ksi) against 540 MPa (78.3 ksi) for NiCo20Cr20MoTi-ST, about 48% more; tensile strength follows at 1,050 MPa (152 ksi) vs 880 MPa (128 ksi). In exchange, NiCo20Cr20MoTi-ST is the more ductile: elongation 42% versus 15% for NiCo20Cr20MoTi-CD, and NiCo20Cr20MoTi-CD is harder (305 HB vs 190 HB). NiCo20Cr20MoTi-ST runs hotter in service (800°C vs 600°C continuous). On the shop floor, NiCo20Cr20MoTi-ST welds better (very good vs fair).
NiCo20Cr20MoTi-CDChoose it when strength drives the design.
NiCo20Cr20MoTi-STChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
NiCo20Cr20MoTi-CD vs NiCo20Cr20MoTi-ST: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
NiCo20Cr20MoTi-CDNiCo20Cr20MoTi-ST
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 221 GPa32.1 Msi · Shear Modulus 85 GPa12.3 Msi · Bulk Modulus 184 GPa26.7 Msi · Poisson's Ratio 0.3 · Hardness, Rockwell B 92 HRB
Physical
Density and transition temperatures.
Same in both: Density 8.36 g/cm³0.3 lb/in³ · Melting Point (Solidus) 1,300°C2,372 °F · Liquidus Temperature 1,355°C2,471 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 11.7 W/m·K6.8 BTU/hr·ft·°F · Specific Heat Capacity 461 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.7 µm/m·K6.5 µin/in·°F · Latent Heat of Fusion 290 J/g125 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 1.5 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.15 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 35 / 100 · Brazeability / Solderability 60 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 235 MJ/kg101,032 BTU/lb · Embodied Carbon (primary production) 17 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
NiCo20Cr20MoTi-CD vs NiCo20Cr20MoTi-ST — frequently asked
Is NiCo20Cr20MoTi-CD stronger than NiCo20Cr20MoTi-ST?
Yes. NiCo20Cr20MoTi-CD has a typical yield strength of 800 MPa (116 ksi) against 540 MPa (78.3 ksi) for NiCo20Cr20MoTi-ST — about 48% more. Tensile strength is 1,050 MPa (152 ksi) vs 880 MPa (128 ksi).
Which condition does FabDigit quote by default, CD or ST?
ST is the default NiCo20Cr20MoTi condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, NiCo20Cr20MoTi-CD or NiCo20Cr20MoTi-ST?
NiCo20Cr20MoTi-ST. Its weldability rates very good (75/100) against fair (45/100) for NiCo20Cr20MoTi-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in NiCo20Cr20MoTi-CD and NiCo20Cr20MoTi-ST side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.