Nickel 205-ANN vs Nickel 205-H
Nickel Alloy · Nickel 205 temper comparison
Nickel 205-ANN and Nickel 205-H are two conditions of the same nickel alloy grade, Nickel 205: ANN (annealed) versus H (hardened). The chemistry is identical, so every difference below comes from the condition. Nickel 205-H is the stronger of the two: yield strength 690 MPa (100 ksi) against 145 MPa (21 ksi) for Nickel 205-ANN, about 4.8 times as much; tensile strength follows at 760 MPa (110 ksi) vs 440 MPa (63.8 ksi). In exchange, Nickel 205-ANN is the more ductile: elongation 45% versus 5% for Nickel 205-H, and Nickel 205-H is harder (215 HB vs 95 HB). Nickel 205-ANN runs hotter in service (315°C vs 260°C continuous). On the shop floor, Nickel 205-H machines more easily (fair vs poor) and Nickel 205-ANN welds better (80 vs 70 out of 100).
Nickel 205-ANNChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Nickel 205-HChoose it when strength drives the design, or when the part is machined in volume.
Nickel 205-ANN vs Nickel 205-H: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 76 GPa11 Msi · Bulk Modulus 180 GPa26.1 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 8.89 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,435°C2,615 °F · Liquidus Temperature 1,446°C2,635 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 456 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 13.3 µm/m·K7.4 µin/in·°F · Latent Heat of Fusion 297 J/g128 BTU/lb · Min Service Temperature -250°C-418 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V · Corrosion Resistance 70 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 35 / 100 · Brazeability / Solderability 80 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 165 MJ/kg70,937 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 320 L/kg38.3 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Nickel 205-ANN vs Nickel 205-H — frequently asked
Is Nickel 205-H stronger than Nickel 205-ANN?
Yes. Nickel 205-H has a typical yield strength of 690 MPa (100 ksi) against 145 MPa (21 ksi) for Nickel 205-ANN — about 4.8 times as much. Tensile strength is 760 MPa (110 ksi) vs 440 MPa (63.8 ksi).
Which condition does FabDigit quote by default, ANN or H?
ANN is the default Nickel 205 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Nickel 205-ANN or Nickel 205-H?
Nickel 205-H. Its machinability rates fair (42/100) against poor (32/100) for Nickel 205-ANN; for welding the order is Nickel 205-ANN first (very good, 80/100) then Nickel 205-H (very good, 70/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Nickel 205-ANN and Nickel 205-H side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.