Nickel Alloy IN-713C-HIP vs IN-713C-SR
Nickel Alloy · IN-713C temper comparison
IN-713C-HIP and IN-713C-SR are two conditions of the same nickel alloy grade, IN-713C: HIP (hot isostatic pressed) versus SR (stress relieved). The chemistry is identical, so every difference below comes from the condition. IN-713C-HIP is the stronger of the two: tensile strength 910 MPa (132 ksi) against 860 MPa (125 ksi) for IN-713C-SR, about 6% more. IN-713C-HIP is the more ductile: elongation 10% versus 8% for IN-713C-SR, and IN-713C-HIP is harder (35 HRC vs 33 HRC).
IN-713C-HIPChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
IN-713C-HIP vs IN-713C-SR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 180 GPa26.1 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 7.91 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,260°C2,300 °F · Liquidus Temperature 1,345°C2,453 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 10.9 W/m·K6.3 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.6 µm/m·K5.9 µin/in·°F · Latent Heat of Fusion 290 J/g125 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.3 % IACS · Electrical Resistivity 1.32×10⁻⁶ Ω·m52 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.15 V · Corrosion Resistance 68 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Same in both: Formability (cold) 3 / 100 · Castability 88 / 100 · Brazeability / Solderability 45 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 190 MJ/kg81,685 BTU/lb · Embodied Carbon (primary production) 13.5 kg CO₂/kg · Embodied Water 400 L/kg47.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
IN-713C-HIP vs IN-713C-SR — frequently asked
Is IN-713C-HIP stronger than IN-713C-SR?
Yes. IN-713C-HIP has a typical tensile strength of 910 MPa (132 ksi) against 860 MPa (125 ksi) for IN-713C-SR — about 6% more.
Which condition does FabDigit quote by default, HIP or SR?
F is the default IN-713C condition in the FabDigit quote flow (neither HIP nor SR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose IN-713C-HIP over IN-713C-SR?
Pick IN-713C-HIP when strength drives the design, or when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in IN-713C-HIP and IN-713C-SR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.