Nickel Alloy Hastelloy B-2-AW vs Hastelloy B-2-CW
Nickel Alloy · Hastelloy B-2 temper comparison
Hastelloy B-2-AW and Hastelloy B-2-CW are two conditions of the same nickel alloy grade, Hastelloy B-2: AW (as-welded deposit) versus CW (cold worked). The chemistry is identical, so every difference below comes from the condition. Hastelloy B-2-CW is the stronger of the two: yield strength 860 MPa (125 ksi) against 470 MPa (68.2 ksi) for Hastelloy B-2-AW, about 83% more; tensile strength follows at 1,150 MPa (167 ksi) vs 830 MPa (120 ksi). In exchange, Hastelloy B-2-AW is the more ductile: elongation 35% versus 15% for Hastelloy B-2-CW, and Hastelloy B-2-CW is harder (300 HB vs 215 HB).
Hastelloy B-2-AWChoose it when the part is bent, formed or impact-loaded.
Hastelloy B-2-CWChoose it when strength drives the design.
Hastelloy B-2-AW vs Hastelloy B-2-CW: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Hastelloy B-2-AWHastelloy B-2-CW
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 82 GPa11.9 Msi · Bulk Modulus 200 GPa29 Msi · Poisson's Ratio 0.32
Physical
Density and transition temperatures.
Same in both: Density 9.22 g/cm³0.33 lb/in³ · Melting Point (Solidus) 1,330°C2,426 °F · Liquidus Temperature 1,380°C2,516 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 373 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.3 µm/m·K5.7 µin/in·°F · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 30 / 100 · Brazeability / Solderability 50 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 185 MJ/kg79,536 BTU/lb · Embodied Carbon (primary production) 14.5 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Hastelloy B-2-AW vs Hastelloy B-2-CW — frequently asked
Is Hastelloy B-2-CW stronger than Hastelloy B-2-AW?
Yes. Hastelloy B-2-CW has a typical yield strength of 860 MPa (125 ksi) against 470 MPa (68.2 ksi) for Hastelloy B-2-AW — about 83% more. Tensile strength is 1,150 MPa (167 ksi) vs 830 MPa (120 ksi).
Which condition does FabDigit quote by default, AW or CW?
SA is the default Hastelloy B-2 condition in the FabDigit quote flow (neither AW nor CW). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Hastelloy B-2-AW or Hastelloy B-2-CW?
Hastelloy B-2-CW, by a small margin. Both rate poor for machinability — 25/100 against 20/100 for Hastelloy B-2-AW; for welding the order is Hastelloy B-2-AW first (very good, 70/100) then Hastelloy B-2-CW (good, 65/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Hastelloy B-2-AW and Hastelloy B-2-CW side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.