Nickel Alloy ENiCrFe-3 vs ENiCrMo-10
Nickel Alloy · grade comparison
Nickel Alloy ENiCrFe-3 and ENiCrMo-10 are both nickel alloy grades. ENiCrMo-10 is the stronger of the two: yield strength 500 MPa (72.5 ksi) against 420 MPa (60.9 ksi) for ENiCrFe-3, about 19% more; tensile strength follows at 760 MPa (110 ksi) vs 620 MPa (89.9 ksi). ENiCrMo-10 is harder — 210 HB against 190 HB for ENiCrFe-3 — which matters for wear surfaces and threads. ENiCrFe-3 is lighter (8.3 g/cm³ vs 8.69 g/cm³ for ENiCrMo-10).
ENiCrFe-3Choose it when weight is the constraint.
ENiCrMo-10Choose it when strength drives the design, or when surface hardness matters.
ENiCrFe-3 vs ENiCrMo-10: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Poisson's Ratio 0.31 · Elongation at Break 38%
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Same in both: Max Service Temperature (continuous) 650°C1,202 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Formability (cold)
Brazeability / Solderability
Polishability
Same in both: Machinability Rating (AISI 1212 = 100 %) 12% · Weldability 88 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Shock Resistance Index
Same in both: Thermal Diffusivity 2.8 mm²/s
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | ENiCrFe-3 | ENiCrMo-10 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
ENiCrFe-3 vs ENiCrMo-10 — frequently asked
Is ENiCrMo-10 stronger than ENiCrFe-3?
Yes. ENiCrMo-10 has a typical yield strength of 500 MPa (72.5 ksi) against 420 MPa (60.9 ksi) for ENiCrFe-3 — about 19% more. Tensile strength is 760 MPa (110 ksi) vs 620 MPa (89.9 ksi).
Which is cheaper, ENiCrFe-3 or ENiCrMo-10?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, ENiCrFe-3 or ENiCrMo-10?
ENiCrFe-3, by a small margin. Both rate poor for machinability — 28/100 against 22/100 for ENiCrMo-10.
Ready to make it?
Upload a CAD file and FabDigit prices the part in ENiCrFe-3 and ENiCrMo-10 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.