Nickel Alloy CZ-100-ANN vs CZ-100-HIP
Nickel Alloy · CZ-100 temper comparison
CZ-100-ANN and CZ-100-HIP are two conditions of the same nickel alloy grade, CZ-100: ANN (annealed) versus HIP (hot isostatic pressed). The chemistry is identical, so every difference below comes from the condition. CZ-100-HIP is the stronger of the two: yield strength 165 MPa (23.9 ksi) against 140 MPa (20.3 ksi) for CZ-100-ANN, about 18% more; tensile strength follows at 400 MPa (58 ksi) vs 360 MPa (52.2 ksi). CZ-100-HIP is harder — 105 HB against 95 HB for CZ-100-ANN — which matters for wear surfaces and threads.
CZ-100-HIPChoose it when strength drives the design, or when surface hardness matters.
CZ-100-ANN vs CZ-100-HIP: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 70 GPa10.2 Msi · Bulk Modulus 170 GPa24.7 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 8.85 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,315°C2,399 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 456 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 13.3 µm/m·K7.4 µin/in·°F · Latent Heat of Fusion 297 J/g128 BTU/lb · Max Service Temperature (continuous) 480°C896 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V · Corrosion Resistance 80 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 65 / 100 · Brazeability / Solderability 65 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 165 MJ/kg70,937 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 200 L/kg24 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
CZ-100-ANN vs CZ-100-HIP — frequently asked
Is CZ-100-HIP stronger than CZ-100-ANN?
Yes. CZ-100-HIP has a typical yield strength of 165 MPa (23.9 ksi) against 140 MPa (20.3 ksi) for CZ-100-ANN — about 18% more. Tensile strength is 400 MPa (58 ksi) vs 360 MPa (52.2 ksi).
Which condition does FabDigit quote by default, ANN or HIP?
F is the default CZ-100 condition in the FabDigit quote flow (neither ANN nor HIP). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose CZ-100-ANN over CZ-100-HIP?
Pick CZ-100-HIP when strength drives the design, or when surface hardness matters.
Ready to make it?
Upload a CAD file and FabDigit prices the part in CZ-100-ANN and CZ-100-HIP side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.