Nickel Alloy CZ-100-ANN vs CZ-100-F
Nickel Alloy · CZ-100 temper comparison
CZ-100-ANN and CZ-100-F are two conditions of the same nickel alloy grade, CZ-100: ANN (annealed) versus F (as fabricated). The chemistry is identical, so every difference below comes from the condition. CZ-100-F is the stronger of the two: yield strength 160 MPa (23.2 ksi) against 140 MPa (20.3 ksi) for CZ-100-ANN, about 14% more; tensile strength follows at 380 MPa (55.1 ksi) vs 360 MPa (52.2 ksi). In exchange, CZ-100-ANN is the more ductile: elongation 32% versus 25% for CZ-100-F, and CZ-100-F is harder (110 HB vs 95 HB).
CZ-100-ANNChoose it when the part is bent, formed or impact-loaded.
CZ-100-FChoose it when strength drives the design.
CZ-100-ANN vs CZ-100-F: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 180 GPa26.1 Msi · Shear Modulus 70 GPa10.2 Msi · Bulk Modulus 170 GPa24.7 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 8.85 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,315°C2,399 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 456 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 13.3 µm/m·K7.4 µin/in·°F · Latent Heat of Fusion 297 J/g128 BTU/lb · Max Service Temperature (continuous) 480°C896 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 65 / 100 · Brazeability / Solderability 65 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 165 MJ/kg70,937 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 200 L/kg24 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
CZ-100-ANN vs CZ-100-F — frequently asked
Is CZ-100-F stronger than CZ-100-ANN?
Yes. CZ-100-F has a typical yield strength of 160 MPa (23.2 ksi) against 140 MPa (20.3 ksi) for CZ-100-ANN — about 14% more. Tensile strength is 380 MPa (55.1 ksi) vs 360 MPa (52.2 ksi).
Which condition does FabDigit quote by default, ANN or F?
F is the default CZ-100 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, CZ-100-ANN or CZ-100-F?
CZ-100-ANN. Its weldability rates good (65/100) against good (60/100) for CZ-100-F.
Ready to make it?
Upload a CAD file and FabDigit prices the part in CZ-100-ANN and CZ-100-F side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.