Nickel Alloy Alloy 42-CD vs Alloy 42-H24
Nickel Alloy · Alloy 42 temper comparison
Alloy 42-CD and Alloy 42-H24 are two conditions of the same nickel alloy grade, Alloy 42: CD (cold drawn) versus H24 (strain hardened and partially annealed, half hard). The chemistry is identical, so every difference below comes from the condition. Alloy 42-H24 is the stronger of the two: yield strength 590 MPa (85.6 ksi) against 500 MPa (72.5 ksi) for Alloy 42-CD, about 18% more; tensile strength follows at 700 MPa (102 ksi) vs 640 MPa (92.8 ksi). In exchange, Alloy 42-CD is the more ductile: elongation 18% versus 8% for Alloy 42-H24, and Alloy 42-H24 is harder (214 HB vs 195 HB). Alloy 42-CD runs hotter in service (350°C vs 300°C continuous).
Alloy 42-CDChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Alloy 42-H24Choose it when strength drives the design.
Alloy 42-CD vs Alloy 42-H24: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 57 GPa8.3 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.28
Physical
Density and transition temperatures.
Same in both: Density 8.12 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 10.5 W/m·K6.1 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 4.9 µm/m·K2.7 µin/in·°F · Latent Heat of Fusion 275 J/g118 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.45 V · Corrosion Resistance 32 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Weldability
Formability (cold)
Same in both: Machinability 34 / 100 · Machinability Rating (AISI 1212 = 100 %) 34% · Brazeability / Solderability 80 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 85 MJ/kg36,543 BTU/lb · Embodied Carbon (primary production) 6.5 kg CO₂/kg · Embodied Water 200 L/kg24 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Alloy 42-CD vs Alloy 42-H24 — frequently asked
Is Alloy 42-H24 stronger than Alloy 42-CD?
Yes. Alloy 42-H24 has a typical yield strength of 590 MPa (85.6 ksi) against 500 MPa (72.5 ksi) for Alloy 42-CD — about 18% more. Tensile strength is 700 MPa (102 ksi) vs 640 MPa (92.8 ksi).
Which condition does FabDigit quote by default, CD or H24?
Annealed is the default Alloy 42 condition in the FabDigit quote flow (neither CD nor H24). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, Alloy 42-CD or Alloy 42-H24?
Alloy 42-CD. Its weldability rates good (65/100) against good (60/100) for Alloy 42-H24.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Alloy 42-CD and Alloy 42-H24 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.