Copper Alloy C83800-M01 vs C83800-M05
Copper Alloy · C83800 temper comparison
C83800-M01 and C83800-M05 are two conditions of the same copper alloy grade, C83800: M01 (as sand cast) versus M05 (as plaster cast). The chemistry is identical, so every difference below comes from the condition. C83800-M05 is the stronger of the two: yield strength 124 MPa (18 ksi) against 110 MPa (16 ksi) for C83800-M01, about 13% more; tensile strength follows at 262 MPa (38 ksi) vs 241 MPa (35 ksi). In exchange, C83800-M01 is the more ductile: elongation 25% versus 18% for C83800-M05, and C83800-M05 is harder (62 HB vs 55 HB).
C83800-M01Choose it when the part is bent, formed or impact-loaded.
C83800-M05Choose it when strength drives the design.
C83800-M01 vs C83800-M05: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 90 GPa13.1 Msi · Shear Modulus 34 GPa4.9 Msi · Bulk Modulus 95 GPa13.8 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.6 g/cm³0.31 lb/in³ · Melting Point (Solidus) 843°C1,549 °F · Liquidus Temperature 1,004°C1,839 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 72 W/m·K41.6 BTU/hr·ft·°F · Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 18 µm/m·K10 µin/in·°F · Latent Heat of Fusion 175 J/g75.2 BTU/lb · Max Service Temperature (continuous) 200°C392 °F · Min Service Temperature -100°C-148 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 15 % IACS · Electrical Resistivity 1.15×10⁻⁷ Ω·m4.53 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Same in both: Machinability 88 / 100 · Machinability Rating (AISI 1212 = 100 %) 90% · Weldability 20 / 100 · Castability 88 / 100 · Brazeability / Solderability 80 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 85%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C83800-M01 vs C83800-M05 — frequently asked
Is C83800-M05 stronger than C83800-M01?
Yes. C83800-M05 has a typical yield strength of 124 MPa (18 ksi) against 110 MPa (16 ksi) for C83800-M01 — about 13% more. Tensile strength is 262 MPa (38 ksi) vs 241 MPa (35 ksi).
Which condition does FabDigit quote by default, M01 or M05?
M01 is the default C83800 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose C83800-M01 over C83800-M05?
Pick C83800-M01 when the part is bent, formed or impact-loaded. Pick C83800-M05 when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C83800-M01 and C83800-M05 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.