Copper Alloy C82200-TB00 vs C82200-TF00
Copper Alloy · C82200 temper comparison
C82200-TB00 and C82200-TF00 are two conditions of the same copper alloy grade, C82200: TB00 (solution heat treated) versus TF00 (solution heat treated and precipitation hardened). The chemistry is identical, so every difference below comes from the condition. C82200-TF00 is the stronger of the two: yield strength 415 MPa (60.2 ksi) against 125 MPa (18.1 ksi) for C82200-TB00, about 3.3 times as much; tensile strength follows at 620 MPa (89.9 ksi) vs 275 MPa (39.9 ksi). In exchange, C82200-TB00 is the more ductile: elongation 30% versus 5% for C82200-TF00, and C82200-TF00 is harder (195 HB vs 55 HB). C82200-TF00 runs hotter in service (300°C vs 150°C continuous) and C82200-TF00 conducts heat better (190 W/m·K vs 95 W/m·K).
C82200-TB00Choose it when the part is bent, formed or impact-loaded.
C82200-TF00Choose it when strength drives the design, or when the part sees heat.
C82200-TB00 vs C82200-TF00: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 130 GPa18.9 Msi · Shear Modulus 50 GPa7.3 Msi · Bulk Modulus 115 GPa16.7 Msi · Poisson's Ratio 0.3 · Shear Strength 400 MPa58 ksi · Charpy V-Notch Impact (RT) 14 J10.3 ft·lbf · Hardness, Rockwell B 93 HRB · Hardness, Vickers 205 HV
Physical
Density and transition temperatures.
Same in both: Density 8.75 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,030°C1,886 °F · Liquidus Temperature 1,090°C1,994 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 420 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 17.8 µm/m·K9.9 µin/in·°F · Latent Heat of Fusion 205 J/g88.1 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V · Corrosion Resistance 62 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 50 / 100 · Formability (cold) 15 / 100 · Castability 78 / 100 · Brazeability / Solderability 65 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 85 MJ/kg36,543 BTU/lb · Embodied Carbon (primary production) 6 kg CO₂/kg · Embodied Water 350 L/kg41.9 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C82200-TB00 vs C82200-TF00 — frequently asked
Is C82200-TF00 stronger than C82200-TB00?
Yes. C82200-TF00 has a typical yield strength of 415 MPa (60.2 ksi) against 125 MPa (18.1 ksi) for C82200-TB00 — about 3.3 times as much. Tensile strength is 620 MPa (89.9 ksi) vs 275 MPa (39.9 ksi).
Which condition does FabDigit quote by default, TB00 or TF00?
TF00 is the default C82200 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, C82200-TB00 or C82200-TF00?
C82200-TB00. Its machinability rates fair (35/100) against poor (30/100) for C82200-TF00.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C82200-TB00 and C82200-TF00 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.