Copper Alloy C75700-H04 vs C75700-H10
Copper Alloy · C75700 temper comparison
C75700-H04 and C75700-H10 are two conditions of the same copper alloy grade, C75700: H04 (full hard) versus H10 (extra spring hard). The chemistry is identical, so every difference below comes from the condition. C75700-H10 is the stronger of the two: yield strength 660 MPa (95.7 ksi) against 505 MPa (73.2 ksi) for C75700-H04, about 31% more; tensile strength follows at 710 MPa (103 ksi) vs 565 MPa (81.9 ksi). In exchange, C75700-H04 is the more ductile: elongation 4% versus 2% for C75700-H10, and C75700-H10 is harder (208 HB vs 165 HB).
C75700-H04Choose it when the part is bent, formed or impact-loaded.
C75700-H10Choose it when strength drives the design.
C75700-H04 vs C75700-H10: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 46 GPa6.7 Msi · Bulk Modulus 130 GPa18.9 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.72 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,004°C1,839 °F · Liquidus Temperature 1,038°C1,900 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 45 W/m·K26 BTU/hr·ft·°F · Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 16.2 µm/m·K9 µin/in·°F · Latent Heat of Fusion 180 J/g77.4 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 80 / 100 · Polishability 90 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 65 MJ/kg27,945 BTU/lb · Embodied Carbon (primary production) 4.6 kg CO₂/kg · Embodied Water 250 L/kg30 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C75700-H04 vs C75700-H10 — frequently asked
Is C75700-H10 stronger than C75700-H04?
Yes. C75700-H10 has a typical yield strength of 660 MPa (95.7 ksi) against 505 MPa (73.2 ksi) for C75700-H04 — about 31% more. Tensile strength is 710 MPa (103 ksi) vs 565 MPa (81.9 ksi).
Which condition does FabDigit quote by default, H04 or H10?
H02 is the default C75700 condition in the FabDigit quote flow (neither H04 nor H10). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, C75700-H04 or C75700-H10?
C75700-H10. Its machinability rates fair (38/100) against poor (32/100) for C75700-H04; for welding the order is C75700-H04 first (fair, 40/100) then C75700-H10 (poor, 33/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in C75700-H04 and C75700-H10 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.