Copper Alloy C64700-TD01 vs C64700-TF00
Copper Alloy · C64700 temper comparison
C64700-TD01 and C64700-TF00 are two conditions of the same copper alloy grade, C64700: TD01 (solution heat treated and cold worked, quarter hard) versus TF00 (solution heat treated and precipitation hardened). The chemistry is identical, so every difference below comes from the condition. C64700-TF00 is the stronger of the two: yield strength 415 MPa (60.2 ksi) against 310 MPa (45 ksi) for C64700-TD01, about 34% more; tensile strength follows at 550 MPa (79.8 ksi) vs 415 MPa (60.2 ksi). In exchange, C64700-TD01 is the more ductile: elongation 25% versus 18% for C64700-TF00, and C64700-TF00 is harder (165 HB vs 115 HB). C64700-TF00 runs hotter in service (200°C vs 150°C continuous) and C64700-TF00 conducts heat better (155 W/m·K vs 115 W/m·K).
C64700-TD01Choose it when the part is bent, formed or impact-loaded.
C64700-TF00Choose it when strength drives the design, or when the part sees heat.
C64700-TD01 vs C64700-TF00: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 132 GPa19.1 Msi · Shear Modulus 49 GPa7.1 Msi · Bulk Modulus 130 GPa18.9 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.83 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,030°C1,886 °F · Liquidus Temperature 1,090°C1,994 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 17.6 µm/m·K9.8 µin/in·°F · Latent Heat of Fusion 200 J/g86 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.22 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 75 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 62 MJ/kg26,655 BTU/lb · Embodied Carbon (primary production) 4 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C64700-TD01 vs C64700-TF00 — frequently asked
Is C64700-TF00 stronger than C64700-TD01?
Yes. C64700-TF00 has a typical yield strength of 415 MPa (60.2 ksi) against 310 MPa (45 ksi) for C64700-TD01 — about 34% more. Tensile strength is 550 MPa (79.8 ksi) vs 415 MPa (60.2 ksi).
Which condition does FabDigit quote by default, TD01 or TF00?
TF00 is the default C64700 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, C64700-TD01 or C64700-TF00?
C64700-TF00. Its machinability rates fair (40/100) against poor (33/100) for C64700-TD01.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C64700-TD01 and C64700-TF00 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.