Copper Alloy C19210-H01 vs C19210-H02
Copper Alloy · C19210 temper comparison
C19210-H01 and C19210-H02 are two conditions of the same copper alloy grade, C19210: H01 (quarter hard) versus H02 (half hard). The chemistry is identical, so every difference below comes from the condition. C19210-H02 is the stronger of the two: yield strength 285 MPa (41.3 ksi) against 225 MPa (32.6 ksi) for C19210-H01, about 27% more; tensile strength follows at 320 MPa (46.4 ksi) vs 280 MPa (40.6 ksi). In exchange, C19210-H01 is the more ductile: elongation 15% versus 9% for C19210-H02, and C19210-H02 is harder (110 HV vs 95 HV). C19210-H01 runs hotter in service (230°C vs 210°C continuous).
C19210-H01Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
C19210-H02Choose it when strength drives the design.
C19210-H01 vs C19210-H02: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 121 GPa17.5 Msi · Shear Modulus 45 GPa6.5 Msi · Bulk Modulus 138 GPa20 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.91 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,080°C1,976 °F · Liquidus Temperature 1,084°C1,983 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 385 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 17.6 µm/m·K9.8 µin/in·°F · Latent Heat of Fusion 205 J/g88.1 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.22 V · Corrosion Resistance 55 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 45 / 100 · Brazeability / Solderability 90 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 58 MJ/kg24,936 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 320 L/kg38.3 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C19210-H01 vs C19210-H02 — frequently asked
Is C19210-H02 stronger than C19210-H01?
Yes. C19210-H02 has a typical yield strength of 285 MPa (41.3 ksi) against 225 MPa (32.6 ksi) for C19210-H01 — about 27% more. Tensile strength is 320 MPa (46.4 ksi) vs 280 MPa (40.6 ksi).
Which condition does FabDigit quote by default, H01 or H02?
H04 is the default C19210 condition in the FabDigit quote flow (neither H01 nor H02). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose C19210-H01 over C19210-H02?
Pick C19210-H01 when the part is bent, formed or impact-loaded, or when the part sees heat. Pick C19210-H02 when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C19210-H01 and C19210-H02 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.