Copper Alloy C17300-TD04 vs C17300-TH01
Copper Alloy · C17300 temper comparison
C17300-TD04 and C17300-TH01 are two conditions of the same copper alloy grade, C17300: TD04 (solution heat treated and cold worked, full hard) versus TH01 (TD01 and precipitation hardened). The chemistry is identical, so every difference below comes from the condition. C17300-TH01 is the stronger of the two: yield strength 1,105 MPa (160 ksi) against 660 MPa (95.7 ksi) for C17300-TD04, about 67% more; tensile strength follows at 1,240 MPa (180 ksi) vs 760 MPa (110 ksi). In exchange, C17300-TD04 is the more ductile: elongation 6% versus 4% for C17300-TH01, and C17300-TH01 is harder (375 HB vs 230 HB). C17300-TH01 runs hotter in service (200°C vs 100°C continuous) and C17300-TH01 conducts heat better (130 W/m·K vs 105 W/m·K).
C17300-TD04Choose it when the part is bent, formed or impact-loaded.
C17300-TH01Choose it when strength drives the design, or when the part sees heat.
C17300-TD04 vs C17300-TH01: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 50 GPa7.3 Msi · Bulk Modulus 115 GPa16.7 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 8.26 g/cm³0.3 lb/in³ · Melting Point (Solidus) 865°C1,589 °F · Liquidus Temperature 980°C1,796 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 420 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 17.5 µm/m·K9.7 µin/in·°F · Latent Heat of Fusion 200 J/g86 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.23 V · Corrosion Resistance 62 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 60% · Castability 45 / 100 · Brazeability / Solderability 60 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 120 MJ/kg51,591 BTU/lb · Embodied Carbon (primary production) 7.5 kg CO₂/kg · Embodied Water 350 L/kg41.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C17300-TD04 vs C17300-TH01 — frequently asked
Is C17300-TH01 stronger than C17300-TD04?
Yes. C17300-TH01 has a typical yield strength of 1,105 MPa (160 ksi) against 660 MPa (95.7 ksi) for C17300-TD04 — about 67% more. Tensile strength is 1,240 MPa (180 ksi) vs 760 MPa (110 ksi).
Which condition does FabDigit quote by default, TD04 or TH01?
A is the default C17300 condition in the FabDigit quote flow (neither TD04 nor TH01). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose C17300-TD04 over C17300-TH01?
Pick C17300-TD04 when the part is bent, formed or impact-loaded. Pick C17300-TH01 when strength drives the design, or when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C17300-TD04 and C17300-TH01 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.