Aluminum LM27-T6 vs LM27-TE
Aluminum · LM27 temper comparison
LM27-T6 and LM27-TE are two conditions of the same aluminum grade, LM27: T6 (solution heat treated and artificially aged) versus TE (precipitation (artificially aged) treated from the as-cast condition). The chemistry is identical, so every difference below comes from the condition. LM27-T6 is the stronger of the two: tensile strength 255 MPa (37 ksi) against 215 MPa (31.2 ksi) for LM27-TE, about 19% more. LM27-T6 is the more ductile: elongation 2% versus 1% for LM27-TE, and LM27-TE is harder (105 HB vs 92 HB).
LM27-T6Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
LM27-T6 vs LM27-TE: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 74 GPa10.7 Msi · Shear Modulus 27.5 GPa4 Msi · Bulk Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33 · Compressive Strength 120 MPa17.4 ksi · Fatigue Strength (Endurance Limit) 75 MPa10.9 ksi · Hardness, Vickers 85 HV
Physical
Density and transition temperatures.
Same in both: Density 2.76 g/cm³0.1 lb/in³ · Melting Point (Solidus) 520°C968 °F · Liquidus Temperature 604°C1,119 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 963 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 21.5 µm/m·K11.9 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Max Service Temperature (continuous) 175°C347 °F · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 6.4×10⁻⁸ Ω·m2.52 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.8 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 130% · Weldability 40 / 100 · Castability 85 / 100 · Brazeability / Solderability 20 / 100 · Polishability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12 kg CO₂/kg · Embodied Water 1,100 L/kg132 gal/lb · Typical Recycled Content 90%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
LM27-T6 vs LM27-TE — frequently asked
Is LM27-T6 stronger than LM27-TE?
Yes. LM27-T6 has a typical tensile strength of 255 MPa (37 ksi) against 215 MPa (31.2 ksi) for LM27-TE — about 19% more.
Which condition does FabDigit quote by default, T6 or TE?
M is the default LM27 condition in the FabDigit quote flow (neither T6 nor TE). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose LM27-T6 over LM27-TE?
Pick LM27-T6 when strength drives the design, or when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in LM27-T6 and LM27-TE side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.